参数资料
| 型号： | AGLP030V5-CSG201 |
| 厂商： | Microsemi SoC |
| 文件页数： | 130/134页 |
| 文件大小： | 0K |
| 描述： | IC FPGA IGLOO PLUS 30K 201-CSP |
| 标准包装： | 384 |
| 系列： | IGLOO PLUS |
| 逻辑元件/单元数： | 792 |
| 输入/输出数： | 120 |
| 门数： | 30000 |
| 电源电压： | 1.425 V ~ 1.575 V |
| 安装类型： | 表面贴装 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 201-VFBGA，CSBGA |
| 供应商设备封装： | 201-CSP（8x8） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页当前第130页第131页第132页第133页第134页
Revision 16
3-1
3 – Pin Descriptions and Packaging
Supply Pins
GND
Ground
Ground supply voltage to the core, I/O outputs, and I/O logic.
GNDQ
Ground (quiet)
Quiet ground supply voltage to input buffers of I/O banks. Within the package, the GNDQ plane is
decoupled from the simultaneous switching noise originated from the output buffer ground domain. This
minimizes the noise transfer within the package and improves input signal integrity. GNDQ must always
be connected to GND on the board.
VCC
Core Supply Voltage
Supply voltage to the FPGA core, nominally 1.5 V for IGLOO PLUS V5 devices, and 1.2 V or 1.5 V for
IGLOO PLUS V2 devices. VCC is required for powering the JTAG state machine in addition to VJTAG.
Even when a device is in bypass mode in a JTAG chain of interconnected devices, both VCC and VJTAG
must remain powered to allow JTAG signals to pass through the device.
For IGLOO PLUS V2 devices, VCC can be switched dynamically from 1.2 V to 1.5 V or vice versa. This
allows in-system programming (ISP) when VCC is at 1.5 V and the benefit of low power operation when
VCC is at 1.2 V.
VCCIBx
I/O Supply Voltage
Supply voltage to the bank's I/O output buffers and I/O logic. Bx is the I/O bank number. There are four
I/O banks on low power flash devices plus a dedicated VJTAG bank. Each bank can have a separate
VCCI connection. All I/Os in a bank will run off the same VCCIBx supply. VCCI can be 1.2 V, 1.5 V, 1.8 V,
2.5 V, or 3.3 V, nominal voltage. Unused I/O banks should have their corresponding VCCI pins tied to
GND.
VMVx
I/O Supply Voltage (quiet)
Quiet supply voltage to the input buffers of each I/O bank. x is the bank number. Within the package, the
VMV plane biases the input stage of the I/Os in the I/O banks. This minimizes the noise transfer within
the package and improves input signal integrity. Each bank must have at least one VMV connection, and
no VMV should be left unconnected. All I/Os in a bank run off the same VMVx supply. VMV is used to
provide a quiet supply voltage to the input buffers of each I/O bank. VMVx can be 1.2 V, 1.5 V, 1.8 V,
2.5 V, or 3.3 V, nominal voltage. Unused I/O banks should have their corresponding VMV pins tied to
GND. VMV and VCCI should be at the same voltage within a given I/O bank. Used VMV pins must be
connected to the corresponding VCCI pins of the same bank (i.e., VMV0 to VCCIB0, VMV1 to VCCIB1,
etc.).
VCCPLA/B/C/D/E/F
PLL Supply Voltage
Supply voltage to analog PLL, nominally 1.5 V or 1.2 V, depending on the device.
1.5 V for IGLOO PLUS V5 devices
1.2 V or 1.5 V for IGLOO PLUS V2 devices
When the PLLs are not used, the Microsemi Designer place-and-route tool automatically disables the
unused PLLs to lower power consumption. The user should tie unused VCCPLx and VCOMPLx pins to
ground. Microsemi recommends tying VCCPLx to VCC and using proper filtering circuits to decouple
VCC noise from the PLLs. Refer to the PLL Power Supply Decoupling section of the "Clock Conditioning
Circuits in Low Power Flash Devices and Mixed signal FPGAs " chapter of the IGLOO PLUS FPGA
Fabric User’s Guide for a complete board solution for the PLL analog power supply and ground.
There is one VCCPLF pin on IGLOO PLUS devices.
相关PDF资料 |
PDF描述 |
|---|---|
| A3P250-1QNG132 | IC FPGA 1KB FLASH 250K 132-QFN |
| A3P060-TQ144 | IC FPGA 1KB FLASH 60K 144-TQFP |
| RMC50DRTS-S734 | CONN EDGECARD 100PS DIP .100 SLD |
| ACC40DRTI-S734 | CONN EDGECARD 80POS DIP .100 SLD |
| ASC36DRYI | CONN EDGECARD 72POS .100 DIP SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AGLP030V5-CSG201I | 功能描述:IC FPGA IGLOO PLUS 30K 201-CSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:IGLOO PLUS 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14） |
| AGLP030-V5CSG289 | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:IGLOO PLUS Low-Power Flash FPGAs with FlashFreeze Technology |
| AGLP030V5-CSG289 | 功能描述:IC FPGA IGLOO PLUS 30K 289-CSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:IGLOO PLUS 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14） |
| AGLP030-V5CSG289ES | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:IGLOO PLUS Low-Power Flash FPGAs with FlashFreeze Technology |
| AGLP030-V5CSG289I | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:IGLOO PLUS Low-Power Flash FPGAs with FlashFreeze Technology |
发布紧急采购，3分钟左右您将得到回复。