- 您现在的位置：买卖IC网 > PDF目录201300 > AK1001-9RD5B1 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | AK1001-9RD5B1 |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | METAL, CASE K02, MODULE |
| 文件页数： | 4/31页 |
| 文件大小： | 637K |
| 代理商： | AK1001-9RD5B1 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
Cassette Style
150 Watt DC-DC Converters
K Series
Edition 01/01.2000
12/31
Output Protection
Each output is protected against overvoltages which could
occur due to a failure of the internal control circuit. Voltage
suppressor diodes (which under worst case condition may
become a short circuit) provide the required protection. The
suppressor diodes are not designed to withstand externally
applied overvoltages. Overload at any of the outputs will
cause a shut-down of all outputs. A red LED indicates the
overload condition.
Parallel or Series Connection of Units
Single or double output units with equal nominal output
voltage can be connected in parallel without any precau-
tions using option T.
With option T (current sharing), all units share the current
approximately equally.
Single output units and/or main and second outputs of dou-
ble output units can be connected in series with any other
(similar) output.
Note:
– Parallel connection of double output units should always
include both, main and second output to maintain good
regulation of both outputs.
– Not more than 5 units should be connected in parallel.
– Series connection of second outputs without involving
their main outputs should be avoided as regulation may
be poor.
– The maximum output current is limited by the output with
the lowest current limitation if several outputs are con-
nected in series.
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature
TA max (see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the
Measuring point of case
temperature TC (see: Mechanical Data) will approach the
indicated value
TC max after the warm-up phase. However,
the relationship between
TA and TC depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces.
TA max is therefore, contrary to TC max,
an indicative value only.
Caution: The installer must ensure that under all operat-
ing conditions
TC remains within the limits stated in the
table
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink
allows
TA to be higher than 71°C (e.g. 85°C) if TC max is not
exceeded.
For -7 or -9 units at an ambient temperature
TA of 85
°C with
only convection cooling, the maximum permissible current
for each output is approx. 40% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [°C]
0.9
1.0
Forced cooling
05089
TA min
TC max
Convection cooling
Fig. 7
Output current derating versus temperature for -7 and -9
units.
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
TC max. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
It is recommended that continuous operation under simul-
taneous extreme worst case conditions of the following
three parameters be avoided: Minimum input voltage,
maximum output power and maximum temperature.
Uo1d
t d
Ur
t
Uo2d
<10
s
<10
s
Uo1
Uo2
Io1/Io1 nom
0
0.5
1
Io2/Io2 nom
05072
Fig. 8
Typical dynamic load regulation of Uo1 and Uo2
相关PDF资料 |
PDF描述 |
|---|---|
| AK1001-9RD9B1 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| AK1301-7RD0B1 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| AK1301-9RD0TB1 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| AK1501-9PD1TB2 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| AK1501-9PDDB2 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AK100-25 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Attenuator |
| AK10-030C | 制造商:Littelfuse 功能描述:TVS AXIAL KA RATED 10KA 30V BI 制造商:Littelfuse 功能描述:TVS Diodes - Transient Voltage Suppressors 30V 10KA TVS BI Axial KA Rated 制造商:Littelfuse 功能描述:DIODE, TVS, 30V, BIDIRECTIONAL, AXIAL LEADED; TVS Polarity:Bidirectional; Reverse Stand-Off Voltage Vrwm:30V; Breakdown Voltage Min:32V; Breakdown Voltage Max:37V; Clamping Voltage Vc Max:58V; Peak Pulse Current Ippm:10kA ;RoHS Compliant: Yes |
| AK10-030C-12 | 功能描述:TVS DIODE 30VWM 58VC AXIAL 制造商:littelfuse inc. 系列:AK10 包装:散装 零件状态:有效 类型:齐纳 单向通道:- 双向通道:1 电压 - 反向关态（典型值）:30V 电压 - 击穿（最小值）:32V 电压 - 箝位（最大值）@ Ipp:58V 电流 - 峰值脉冲（10/1000μs）:10000A（10kA）（8/20μs） 功率 - 峰值脉冲:- 电源线路保护:无 应用:通用 不同频率时的电容:11nF @ 10kHz 工作温度:-55°C ~ 150°C（TJ） 安装类型:通孔 封装/外壳:轴向，直角弯曲（24.15mm 中心） 供应商器件封装:轴向 标准包装:12 |
| AK10-058C | 功能描述:TVS 二极管 - 瞬态电压抑制器 10kA 58V RoHS:否 制造商:Vishay Semiconductors 极性:Bidirectional 工作电压: 击穿电压:58.9 V 钳位电压:77.4 V 峰值浪涌电流:38.8 A 系列: 封装 / 箱体:DO-214AB 最小工作温度:- 55 C 最大工作温度:+ 150 C |
| AK10-058C-12 | 功能描述:TVS DIODE 58VWM 110VC AXIAL 制造商:littelfuse inc. 系列:AK10 包装:散装 零件状态:有效 类型:齐纳 单向通道:- 双向通道:1 电压 - 反向关态（典型值）:58V 电压 - 击穿（最小值）:64V 电压 - 箝位（最大值）@ Ipp:110V 电流 - 峰值脉冲（10/1000μs）:10000A（10kA）（8/20μs） 功率 - 峰值脉冲:- 电源线路保护:无 应用:通用 不同频率时的电容:6.5nF @ 10kHz 工作温度:-55°C ~ 150°C（TJ） 安装类型:通孔 封装/外壳:轴向，直角弯曲（24.15mm 中心） 供应商器件封装:轴向 标准包装:12 |
发布紧急采购，3分钟左右您将得到回复。