- 您现在的位置：买卖IC网 > PDF目录19417 > AL9910ASP-13 (Diodes Inc)IC LED DVR HIGH BRIGHT SO8EP PDF资料下载
参数资料
| 型号： | AL9910ASP-13 |
| 厂商： | Diodes Inc |
| 文件页数： | 11/15页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR HIGH BRIGHT SO8EP |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | 交直流离线开关，PWM |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 背光，通用 |
| 类型 - 次要： | 高亮度 LED（HBLED） |
| 频率： | 25kHz ~ 300kHz |
| 电源电压： | 85 V ~ 277 VAC |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 供应商设备封装： | 8-SO 裸露焊盘 |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | AL9910ASP-13DIDKR |
AL9910/ AL9910A/ AL9910-5
Applications Information (cont.)
DC-DC Buck LED Driver
The design procedure for an ac input buck LED driver outlined in the previous chapters equally applies DC input LED drivers.
When driving long LED chains care should be taken not to induce SBO – maximum LED chain voltage should be less half of V IN . So either
maximum duty cycle should be kept below 50% or use of constant off-time removes this issue.
DC-DC Boost LED Driver
Due to the topology of the AL9910 LED driver-controller it is capable of being used in boost configurations – at reduced accuracy. The accuracy
can be improved by measuring the LED current with an op amp and use the op amp’s output to drive the LD pin.
A Boost LED driver is used when the forward voltage drop of the LED string is higher than the input supply voltage. For example, the Boost
topology can be appropriate when input voltage is supplied by a 48V power supply and the LED string consists of twenty HB LEDs, as the case
may be for a street light.
L1
C1
V DD
V IN
AL9910/A
Q1
D1
V IN
PWM_D
GATE
C2
LD
R OSC
GND
CS
C3
R OSC
R SENSE
Figure 5. Boost LED Driver
In a Boost converter, when the external MOSFET is ON the energy is stored in the inductor which is then delivered to the output when the external
MOSFET switches OFF. If the energy stored in the inductor is not fully depleted by the next switching cycle (continuous conduction mode) the DC
conversion between input and output voltage is given by:
V OUT =
V IN
1 ? D
D =
V OUT ? V IN
V OUT
From the switching frequency, f OSC , the on-time of the MOSFET can be calculated:
t ON =
D
f OSC
From this the required inductor value can be determined by:
L =
V IN ? t ON
0 . 3 ? I LED
The Boost topology LED driver requires an output capacitor to deliver current to the LED string during the time that the external MOSFET is on.
In boost LED driver topologies if the LEDs should become open circuit damage may occur to the power switch and so some form of detection
should be present to provide Over-voltage detection/protection.
AL9910/ AL9910A/ AL9910-5
Document number: DS35103 Rev. 8 - 2
11 of 15
www.diodes.com
December 2012
? Diodes Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J2P-IZ | CONVERTER MOD DC/DC 13.8V 25W |
| VI-BWF-CY-F4 | CONVERTER MOD DC/DC 72V 50W |
| RS3-2412S/H2 | CONV DC/DC 3W 18-36VIN 12VOUT |
| VI-BWD-CY-F2 | CONVERTER MOD DC/DC 85V 50W |
| HWS50-3/A | PWR SUP IND 3.3V 10A SNG OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AL9910EV4 | 功能描述:AL9910A 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:180mA 输出和类型:1，非隔离 电压 - 输出:- 特性:- 电压 - 输入:85 ~ 277 VAC 所含物品:板 使用的 IC/零件:AL9910A 标准包装:1 |
| AL9910EV5 | 功能描述:AL9910A 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:240mA 输出和类型:1，非隔离 电压 - 输出:- 特性:- 电压 - 输入:85 ~ 277 VAC 所含物品:板 使用的 IC/零件:AL9910A 标准包装:1 |
| AL9910EV6 | 功能描述:AL9910A 4, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:75mA 输出和类型:4，非隔离 电压 - 输出:- 特性:- 电压 - 输入:90 ~ 132 VAC 所含物品:板 使用的 IC/零件:AL9910A 标准包装:1 |
| AL9910EV8 | 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:Non-Dimmable 120VAC Evaluation Board |
| AL9910S-13 | 功能描述:LED照明驱动器 7.5V LED Driver PWM 85 to 265VAC Mosfet RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。