- 您现在的位置：买卖IC网 > PDF目录19417 > AL9910ASP-13 (Diodes Inc)IC LED DVR HIGH BRIGHT SO8EP PDF资料下载
参数资料
| 型号： | AL9910ASP-13 |
| 厂商： | Diodes Inc |
| 文件页数： | 9/15页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR HIGH BRIGHT SO8EP |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | 交直流离线开关，PWM |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 背光，通用 |
| 类型 - 次要： | 高亮度 LED（HBLED） |
| 频率： | 25kHz ~ 300kHz |
| 电源电压： | 85 V ~ 277 VAC |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 供应商设备封装： | 8-SO 裸露焊盘 |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | AL9910ASP-13DIDKR |
AL9910/ AL9910A/ AL9910-5
Applications Information (cont.)
Dimming
The LED brightness can be dimmed either linearly (using the LD pin) or via pulse width modulation (using the PWM-D pin); or a combination of
both - depending on the application. Pulling the PWM_D pin to ground will turn off the AL9910. When disabled, the AL9910’s quiescent current is
typically 0.5mA (0.65 for AL9910A). Reducing the LD voltage will reduce the LED current but it will not entirely turn off the external power
transistor and hence the LED current – this is due to the finite blanking period. Only the PWM_D pin will turn off the power transistor.
Linear dimming is accomplished by applying a 45mV to 250mV analog signal to the LD pin. This overrides the default 250mV threshold level of the
CS pin and reduces the output current. If an input voltage greater than 250mV is applied to the LD then the output current will not change.
The LD pin also provides a simple cost effective solution to soft start; by connecting a capacitor to the LD pin down to ground at initial power up
the LD pin will be held low causing the sense threshold to be low. As the capacitor charges up the current sense threshold will increase thereby
causing the average LED current to increase.
PWM dimming is achieved by applying an external PWM signal to the PWM_D pin. The LED current is proportional to the PWM duty cycle and the
light output can be adjusted between zero and 100%. The PWM signal enables and disables the AL9910 - modulating the LED current. The
ultimate accuracy of the PWM dimming method is limited only by the minimum gate pulse width, which is a fraction of a percentage of the low
frequency duty cycle. PWM dimming of the LED light can be achieved by turning on and off the converter with low frequency 50Hz to 1000Hz TTL
logic level signal.
With both modes of dimming it is not possible to achieve average brightness levels higher than the one set by the current sense threshold level of
the AL9910. I f a greater LED current is required then a smaller sense resistor should be used
Output Open Circuit Protection
The non-isolated buck LED driver topology provides inherent protection against an open circuit condition in the LED string due to the LEDs being
connected in series with the inductor. Should the LED string become open circuit then no switching occurs and the circuit can be permanently left
in this state with damage to the rest of the circuit.
AC/DC Off-Line LED Driver
The AL9910 is a cost-effective off-line buck LED driver-controller specifically designed for driving LED strings. It is suitable for being used with
either rectified AC line or any DC voltage between 15V to 500V. See Figure 3 for typical circuit.
LED +
D1
C3
V AC IN
BR1
C1
C2
V DD
LD
V IN
AL9910/A
GATE
Q1
L1
LED -
PWM_D
CS
R OSC
GND
R SENSE
R OSC
Figure 3. Typical Application Circuit (without PFC)
Buck Design Equations:
D =
V LEDs
V IN
t ON =
D
f osc
L ≥
( V IN ? V LEDs ) × t ON
0 . 3 × I LED
R SENSE =
0 . 25
I LED + ( 0 . 5 × ( I LED × 0 . 3 ))
where I LED x 0.3 = I RIPPLE
AL9910/ AL9910A/ AL9910-5
Document number: DS35103 Rev. 8 - 2
9 of 15
www.diodes.com
December 2012
? Diodes Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J2P-IZ | CONVERTER MOD DC/DC 13.8V 25W |
| VI-BWF-CY-F4 | CONVERTER MOD DC/DC 72V 50W |
| RS3-2412S/H2 | CONV DC/DC 3W 18-36VIN 12VOUT |
| VI-BWD-CY-F2 | CONVERTER MOD DC/DC 85V 50W |
| HWS50-3/A | PWR SUP IND 3.3V 10A SNG OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AL9910EV4 | 功能描述:AL9910A 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:180mA 输出和类型:1，非隔离 电压 - 输出:- 特性:- 电压 - 输入:85 ~ 277 VAC 所含物品:板 使用的 IC/零件:AL9910A 标准包装:1 |
| AL9910EV5 | 功能描述:AL9910A 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:240mA 输出和类型:1，非隔离 电压 - 输出:- 特性:- 电压 - 输入:85 ~ 277 VAC 所含物品:板 使用的 IC/零件:AL9910A 标准包装:1 |
| AL9910EV6 | 功能描述:AL9910A 4, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:75mA 输出和类型:4，非隔离 电压 - 输出:- 特性:- 电压 - 输入:90 ~ 132 VAC 所含物品:板 使用的 IC/零件:AL9910A 标准包装:1 |
| AL9910EV8 | 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:Non-Dimmable 120VAC Evaluation Board |
| AL9910S-13 | 功能描述:LED照明驱动器 7.5V LED Driver PWM 85 to 265VAC Mosfet RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。