- 您现在的位置：买卖IC网 > PDF目录366440 > AM29F400BT-90SF0 (Advanced Micro Devices, Inc.) 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory PDF资料下载
参数资料
| 型号： | AM29F400BT-90SF0 |
| 厂商： | Advanced Micro Devices, Inc. |
| 英文描述： | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| 中文描述： | 4兆位（512亩x 8-Bit/256亩x 16位），5.0伏的CMOS只引导扇区闪存 |
| 文件页数： | 10/43页 |
| 文件大小： | 548K |
| 代理商： | AM29F400BT-90SF0 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
8
Am29F400B
21505E5 November1,2006
D A T A S H E E T
DEVICE BUS OPERATIONS
This section describes the requirements and use of the
device bus operations, which are initiated through the
internal command register. The command register
itself does not occupy any addressable memory loca-
tion. The register is composed of latches that store the
commands, along with the address and data informa-
tion needed to execute the command. The contents of
the register serve as inputs to the internal state
machine. The state machine outputs dictate the func-
tion of the device. Table 1 lists the device bus
operations, the inputs and control levels they require,
and the resulting output. The following subsections
describe each of these operations in further detail.
Table 1.
Am29F400B Device Bus Operations
Legend:
L = Logic Low = V
IL
, H = Logic High = V
IH
, V
ID
= 12.0
±
0.5 V, X = Don’t Care, D
IN
= Data In, D
OUT
= Data Out, A
IN
= Address In
Note:
See the sections onSector Group Protection and Temporary Sector Unprotect for more information.
Word/Byte Configuration
The BYTE# pin controls whether the device data I/O
pins DQ15–DQ0 operate in the byte or word configura-
tion. If the BYTE# pin is set at logic ‘1’, the device is in
word configuration, DQ15–DQ0 are active and con-
trolled by CE# and OE#.
If the BYTE# pin is set at logic ‘0’, the device is in byte
configuration, and only data I/O pins DQ0–DQ7 are
active and controlled by CE# and OE#. The data I/O
pins DQ8–DQ14 are tri-stated, and the DQ15 pin is
used as an input for the LSB (A-1) address function.
Requirements for Reading Array Data
To read array data from the outputs, the system must
drive the CE# and OE# pins to V
IL
. CE# is the power
control and selects the device. OE# is the output
control and gates array data to the output pins. WE#
should remain at V
IH
. The BYTE# pin determines
whether the device outputs array data in words or
bytes.
The internal state machine is set for reading array data
upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory
content occurs during the power transition. No
command is necessary in this mode to obtain array
data. Standard microprocessor read cycles that assert
valid addresses on the device address inputs produce
valid data on the device data outputs. The device
remains enabled for read access until the command
register contents are altered.
See “Reading Array Data” for more information. Refer
to the AC Read Operations table for timing specifica-
tions and to Figure 9 for the timing diagram. I
CC1
in the
DC Characteristics table represents the active current
specification for reading array data.
Writing Commands/Command Sequences
To write a command or command sequence (which
includes programming data to the device and erasing
sectors of memory), the system must drive WE# and
CE# to V
IL
, and OE# to V
IH
.
For program operations, the BYTE# pin determines
whether the device accepts program data in bytes or
words. Refer to “Word/Byte Configuration” for more
information.
An erase operation can erase one sector, multiple sec-
tors, or the entire device. Tables 2 and 3 indicate the
address space that each sector occupies. A “sector
address” consists of the address bits required to
uniquely select a sector. The “Command Definitions”
section has details on erasing a sector or the entire
chip, or suspending/resuming the erase operation.
Operation
CE#
L
L
V
CC
±
0.5 V
H
L
X
X
OE#
L
H
WE#
H
L
RESET#
H
H
V
CC
±
0.5 V
H
H
L
V
ID
A0–A17
A
IN
A
IN
DQ0–DQ7
D
OUT
D
IN
DQ8–DQ15
BYTE#
= V
IH
D
OUT
D
IN
BYTE#
= V
IL
High-Z
High-Z
Read
Write
CMOS Standby
X
X
X
High-Z
High-Z
High-Z
TTL Standby
Output Disable
Hardware Reset
Temporary Sector Unprotect (See Note)
X
H
X
X
X
H
X
X
X
X
X
High-Z
High-Z
High-Z
D
IN
High-Z
High-Z
High-Z
D
IN
High-Z
High-Z
High-Z
X
A
IN
相关PDF资料 |
PDF描述 |
|---|---|
| AM29F400BT-90SI | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| AM29F400BT-90SI0 | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| AM29F400BT-90SK | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| AM29F400BT-90SK0 | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory |
| AM29F800B-120FE | 8 Megabit (1,048,576 x 8-Bit/524,288 x 16-Bit) CMOS 5.0 Volt-only, Sector Erase Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AM29F400BT-90SI | 制造商:Spansion 功能描述: |
| AM29F800BB-120DPC1 | 制造商:Spansion 功能描述:5V 8M FLASH KNOWN GOOD DIE W/BOTTOM BOOT (COMMERCIAL TEMP) - Gel-pak, waffle pack, wafer, diced wafer on film |
| AM29F800BB120SC | 制造商:Advanced Micro Devices 功能描述: |
| AM29F800BB-55EC | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 8Mbit 1M/512K x 8bit/16bit 55ns 48-Pin TSOP |
| AM29F800BB-55EF | 功能描述:闪存 8M (1MX8/512KX16) Parallel NOR Fl 5V RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。