- 您现在的位置：买卖IC网 > PDF目录366448 > Am29LV001BT-45RFIB (Advanced Micro Devices, Inc.) 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory PDF资料下载
参数资料
| 型号： | Am29LV001BT-45RFIB |
| 厂商： | Advanced Micro Devices, Inc. |
| 英文描述： | 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| 中文描述： | 1兆位（128亩× 8位）的CMOS 3.0伏，只引导扇区闪存 |
| 文件页数： | 19/38页 |
| 文件大小： | 221K |
| 代理商： | AM29LV001BT-45RFIB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
19
Am29LV001B
P R E L IM IN A R Y
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has
exceeded a specified internal pulse count limit. Under
these conditions DQ5 produces a “1.” This is a failure
condition that indicates the program or erase cycle was
not successfully completed.
The DQ5 failure condition may appear if the system
tries to program a “1” to a location that is previously pro-
grammed to “0.”
Only an erase operation can change
a “0” back to a “1.”
Under this condition, the device
halts the operation, and when the operation has ex-
ceeded the timing limits, DQ5 produces a “1.”
Under both these conditions, the system must issue the
reset command to return the device to reading array
data.
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not an
erase operation has begun. (The sector erase timer
does not apply to the chip erase command.) If additional
sectors are selected for erasure, the entire time-out also
applies after each additional sector erase command.
When the time-out is complete, DQ3 switches from “0” to
“1.” If the time between additional sector erase com-
mands from the system can be assumed to be less than
50 μs, the system need not monitor DQ3. See also the
“Sector Erase Command Sequence” section.
After the sector erase command sequence is written,
the system should read the status on DQ7 (Data# Poll-
ing) or DQ6 (Toggle Bit I) to ensure the device has ac-
cepted the command sequence, and then read DQ3. If
DQ3 is “1”, the internally controlled erase cycle has be-
gun; all further commands (other than Erase Suspend)
are ignored until the erase operation is complete. If
DQ3 is “0”, the device will accept additional sector
erase commands. To ensure the command has been
accepted, the system software should check the status
of DQ3 prior to and following each subsequent sector
erase command. If DQ3 is high on the second status
check, the last command might not have been ac-
cepted. Table 6 shows the outputs for DQ3.
START
No
Yes
Yes
DQ5 = 1
No
Yes
Toggle Bit
= Toggle
No
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Read DQ7–DQ0
Toggle Bit
= Toggle
Read DQ7–DQ0
Twice
Read DQ7–DQ0
Notes:
1. Read toggle bit twice to determine whether or not it is
toggling. See text.
2. Recheck toggle bit because it may stop toggling as DQ5
changes to “1”. See text.
21557C-9
Figure 6.
Toggle Bit Algorithm
(Note 1)
(Notes
1, 2)
相关PDF资料 |
PDF描述 |
|---|---|
| AM29LV001BT-45RJC | 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV001BT-45RJCB | 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| Am29LV001BT-45RJE | 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV001BT-45RJI | 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV001BT-55ECB | 1 Megabit (128 K x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AM29LV001BT-55ED | 制造商:Spansion 功能描述:1M (128KX8) 3V, BOOT BLOCK, TOP, TSOP32, COM - Trays |
| AM29LV002BB-90EC | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV002BT-90EF | 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 2Mbit 256K x 8bit 90ns 40-Pin TSOP |
| AM29LV002BT-90EI\\T | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 2MBIT 256KX8 90NS 40TSOP - Tape and Reel |
| AM29LV002BT-90EI\T | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 2MBIT 256KX8 90NS 40TSOP - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。