- 您现在的位置：买卖IC网 > PDF目录223348 > AM29LV004B-90ED (SPANSION LLC) 512K X 8 FLASH 3V PROM, 90 ns, PDSO40 PDF资料下载
参数资料
| 型号： | AM29LV004B-90ED |
| 厂商： | SPANSION LLC |
| 元件分类： | PROM |
| 英文描述： | 512K X 8 FLASH 3V PROM, 90 ns, PDSO40 |
| 封装： | PLASTIC, TSOP-40 |
| 文件页数： | 35/36页 |
| 文件大小： | 459K |
| 代理商： | AM29LV004B-90ED |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页
8
Am29LV004
PR EL I M I NAR Y
Standby Mode
When the system is not reading or writing to the device,
it can place the device in the standby mode. In this
mode, current consumption is greatly reduced, and the
outputs are placed in the high impedance state, inde-
pendent of the OE# input.
The device enters the CMOS standby mode when the
CE# and RESET# pins are both held at VCC ± 0.3 V.
(Note that this is a more restricted voltage range than
VIH.) If CE# and RESET# are held at VIH, but not within
VCC ± 0.3 V, the device will be in the standby mode, but
the standby current will be greater. The device requires
standard access time (tCE) for read access when the
device is in either of these standby modes, before it is
ready to read data.
If the device is deselected during erasure or program-
min g, the d evice dra ws active current u ntil th e
operation is completed.
sents the standby current specification.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device
en ergy co nsu mp tion . The d evice au tomat ic ally
enables this mode when addresses remain stable for
tACC + 30 ns. The automatic sleep mode is indepen-
dent of the CE#, WE#, and OE# control signals. Stan-
dard address access timings provide new data when
addresses are changed. While in sleep mode, output
data is latched and always available to the system. ICC5
in the DC Characteristics table represents the auto-
matic sleep mode current specification.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of reset-
ting the device to reading array data. When the RE-
SET# pin is driven low for at least a period of tRP, the
device immediately terminates any operation in
progress, tristates all output pins, and ignores all
read/write commands for the duration of the RESET#
pulse. The device also resets the internal state ma-
chine to reading array data. The operation that was in-
terrupted should be reinitiated once the device is ready
to accept another command sequence, to ensure data
integrity.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at VSS±0.3 V, the device
draws CMOS standby current (ICC4). If RESET# is held
at VIL but not within VSS±0.3 V, the standby current will
be greater.
The RESET# pin may be tied to the system reset cir-
cuitry. A system reset would thus also reset the Flash
memory, enabling the system to read the boot-up firm-
ware from the Flash memory.
If RESET# is asserted during a program or erase op-
eration, the RY/BY# pin remains a “0” (busy) until the
internal reset operation is complete, which requires a
time of tREADY (during Embedded Algorithms). The
syst em can thu s monito r RY/BY# to det ermine
whether the reset operation is complete. If RESET# is
asserted when a program or erase operation is not ex-
ecuting (RY/BY# pin is “1”), the reset operation is
completed within a time of tREADY (not during Embed-
ded Algorithms). The system can read data tRH after
the RESET# pin returns to VIH.
Refer to the AC Characteristics tables for RESET# pa-
rameters and to Figure 13 for the timing diagram.
Output Disable Mode
When the OE# input is at VIH, output from the device is
disabled. The output pins are placed in the high imped-
ance state.
相关PDF资料 |
PDF描述 |
|---|---|
| Am29LV400B-90RWACB | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| Am29LV400B-90RWAE | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| Am29LV400B-90RWAEB | CAP 0.47UF 50V +50-20% X7R SMD-0612 TR-7 PLATED-NI/SN HC-FEEDTHRU |
| Am29LV400BB70RWACB | Ceramic Multilayer Capacitor; Capacitance:470pF; Capacitance Tolerance:+50, -20 %; Working Voltage, DC:50V; Dielectric Characteristic:X7R; Package/Case:1206; Series:W3F; Leaded Process Compatible:Yes |
| Am29LV400BB70RWAE | 4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AM29LV004BB-120EC | 制造商:Advanced Micro Devices 功能描述:NOR Flash, 512K x 8, 40 Pin, Plastic, TSSOP |
| AM29LV004BB-120EI | 制造商:Rochester Electronics LLC 功能描述: 制造商:Advanced Micro Devices 功能描述:NOR Flash, 512K x 8, 40 Pin, Plastic, TSSOP |
| AM29LV004BB120EI\T | 制造商:Advanced Micro Devices 功能描述:4 Mb (512K x 8) Boot Sector, Flash Memory |
| AM29LV004BB-120EIT | 制造商:Rochester Electronics LLC 功能描述: 制造商:Advanced Micro Devices 功能描述: |
| am29lv004bt-120ed | 制造商:Advanced Micro Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。