参数资料
型号: AM29LV200BT-70RSC
厂商: ADVANCED MICRO DEVICES INC
元件分类: PROM
英文描述: 256K X 8 FLASH 3V PROM, 70 ns, PDSO44
封装: MO-180AA, SOP-44
文件页数: 10/41页
文件大小: 843K
代理商: AM29LV200BT-70RSC
18
Am29LV200B
WRITE OPERATION STATUS
The device provides several bits to determine the
status of a write operation: DQ2, DQ3, DQ5, DQ6,
DQ7, and RY/BY#. Table 6 and the following subsec-
tions describe the functions of these bits. DQ7,
RY/BY#, and DQ6 each offer a method for determining
whether a program or erase operation is complete or in
progress. These three bits are discussed first.
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host
system whether an Embedded Algorithm is in progress
or completed, or whether the device is in Erase Sus-
pend. Data# Polling is valid after the rising edge of the
final WE# pulse in the program or erase command
sequence.
During the Embedded Program algorithm, the device
outputs on DQ7 the complement of the datum pro-
grammed to DQ7. This DQ7 status also applies to
programming during Erase Suspend. When the
Embedded Program algorithm is complete, the device
outputs the datum programmed to DQ7. The system
must provide the program address to read valid status
information on DQ7. If a program address falls within a
protected sector, Data# Polling on DQ7 is active for
approximately 1 s, then the device returns to reading
array data.
During the Embedded Erase algorithm, Data# Polling
produces a “0” on DQ7. When the Embedded Erase
algorithm is complete, or if the device enters the Erase
Suspend mode, Data# Polling produces a “1” on DQ7.
This is analogous to the complement/true datum output
described for the Embedded Program algorithm: the
erase function changes all the bits in a sector to “1”;
prior to this, the device outputs the “complement,” or
“0.” The system must provide an address within any of
the sectors selected for erasure to read valid status
information on DQ7.
After an erase command sequence is written, if all
sectors selected for erasing are protected, Data#
Polling on DQ7 is active for approximately 100 s, then
the device returns to reading array data. If not all
selected sectors are protected, the Embedded Erase
algorithm erases the unprotected sectors, and ignores
the selected sectors that are protected.
When the system detects DQ7 has changed from the
complement to true data, it can read valid data at DQ7–
DQ0 on the following read cycles. This is because DQ7
may change asynchronously with DQ0–DQ6 while
Output Enable (OE#) is asserted low. Figure 19, Data#
Polling Timings (During Embedded Algorithms), in the
“AC Characteristics” section illustrates this.
Table 6 shows the outputs for Data# Polling on DQ7.
Figure 5 shows the Data# Polling algorithm.
DQ7 = Data?
Yes
No
DQ5 = 1?
No
Yes
FAIL
PASS
Read DQ7–DQ0
Addr = VA
Read DQ7–DQ0
Addr = VA
DQ7 = Data?
START
Notes:
1. VA = Valid address for programming. During a sector
erase operation, a valid address is an address within any
sector selected for erasure. During chip erase, a valid
address is any non-protected sector address.
2. DQ7 should be rechecked even if DQ5 = “1” because
DQ7 may change simultaneously with DQ5.
21521D-8
Figure 5.
Data# Polling Algorithm
相关PDF资料
PDF描述
AM29LV200BB-70RSI 256K X 8 FLASH 3V PROM, 70 ns, PDSO44
AM29LV320DB120EE 2M X 16 FLASH 3V PROM, 120 ns, PDSO48
AM29LV320DB120WME 2M X 16 FLASH 3V PROM, 120 ns, PBGA48
AM29LV640MH101EF 4M X 16 FLASH 3V PROM, 100 ns, PDSO56
AM2D-11G ACTIVE DELAY LINE, TRUE OUTPUT, PDSO8
相关代理商/技术参数
参数描述
AM29LV256MH120RPGI 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 256MBIT 32MX8/16MX16 120NS 64BGA - Trays
AM29LV256MH123RPGI 制造商:Advanced Micro Devices 功能描述:
AM29LV256MH94REI 制造商:Spansion 功能描述:256M (32MX8/16MX16) 3V REG, MIRRORBIT, TSOP56, IND - Trays
AM29LV320DB120EI 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 32M-Bit 4M x 8/2M x 16 120ns 48-Pin TSOP
AM29LV320DB120WMI 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 32M-Bit 4M x 8/2M x 16 120ns 48-Pin FBGA