参数资料
型号: AMIS30623C623BG
厂商: ON Semiconductor
文件页数: 39/61页
文件大小: 0K
描述: IC MOTOR DRIVER/CTLR 32NQFP
标准包装: 40
应用: 步进电机驱动器
评估套件: 可供
输出数: 1
电流 - 输出: 800mA
电源电压: 6.5 V ~ 29 V
工作温度: -40°C ~ 165°C
安装类型: 表面贴装
封装/外壳: 32-VQFP 裸露焊盘
供应商设备封装: 32-NQFP(7x7)
包装: 管件
AMIS ? 30623
Type #8: eight data bytes preparing frame with 0x3C identifier.
Table 32. PREPARING FRAME #8
Structure
Byte
0
Content
Identifier
Bit 7
0
Bit 6
0
Bit 5
1
Bit 4
1
Bit 3
1
Bit 2
1
Bit 1
0
Bit 0
0
1
Data 1
AppCMD = ...
2
3
4
5
6
7
8
9
Data 2
Data 3
Data 4
Data 5
Data 6
Data 7
Data 8
Checksum
1
1
CMD[6:0]
AD[6:0]
Data4[7:0] FF
Data5[7:0] FF
Data6[7:0] FF
Data7[7:0] FF
Data8[7:0] FF
Checksum over data
Where :
AppCMD: If = ‘0x80’ this indicates that Data 2 contains an application command
CMD[6:0]: Application Command “byte”
AD[6:0]: Slave node physical address
Data[7:0]: Data transmitted
Dynamic Assignment of Identifiers
The identifier field in the LIN datagram denotes the
content of the message. Six identifier bits and two parity bits
are used to represent the content. The identifiers 0x3C and
0x3F are reserved for command frames and extended
frames. Slave nodes need to be very flexible to adapt itself
to a given LIN network in order to avoid conflicts with slave
nodes from different manufacturers. Dynamic assignment
of the identifiers will fulfill this requirement by writing
identifiers into the circuits RAM. ROM pointers are linking
commands and dynamic identifiers together. A writing
frame with identifier 0x3C issued by the LIN master will
write dynamic identifiers into the RAM. One writing frame
is able to assign 4 identifiers; therefore 3 frames are needed
to assign all identifiers. Each ROM pointer <ROMp_x
[3:0]> place the corresponding dynamic identifier
<Dyn_ID_x [5:0]> at the correct place in the RAM (see
Table below: LIN – Dynamic Identifiers Writing Frame).
When setting <Broad> to zero broadcasting is active and
each slave on the LIN bus will store the same dynamic
identifiers, otherwise only the slave with the corresponding
slave address is programmed.
Table 33. DYNAMIC IDENTIFIERS WRITING FRAME
Structure
Byte
Content
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
1
Identifier
AppCMD
0x3C
0x80
2
CMD
1
0x11
3
Address
Broad
AD6
AD5
AD4
AD3
AD2
AD1
AD0
4
Data
DynID_1[3:0]
ROMp_1[3:0]
5
6
7
8
Data
Data
Data
Data
DynID_2[1:0]
ROMp_4[1:0]
ROMp_3[3:0]
DynID_4[5:0]
ROMp_2[3:0]
DynID_3[5:0]
DynID_2[5:2]
DynID_1[5:4]
ROMp_4[3:2]
9
Checksum
Checksum over data
Where :
CMD[6:0]: 0x11, corresponding to dynamic assignment of four LIN identifiers
Broad: If <Broad> = ‘0’ all the circuits connected to the LIN bus will share the same dynamically assigned identifiers.
Dyn_ID_x [5:0]: Dynamically assigned LIN identifier to the application command which ROM pointer is <ROMp_x [3:0]>
One frame allows only assigning of four identifiers. Therefore, additional frames could be needed in order to assign more
identifiers (maximum three for the AMIS ? 30623).
http://onsemi.com
39
相关PDF资料
PDF描述
AMIS39100PNPB3G IC DVR OCT HI SIDE W/PROT 28SOIC
AMIS39101PNPB4G IC DRIVER HIGH SIDE OCTAL 28SOIC
AN8025 IC REG LDO 2.5V 50MA TO-92
AOZ1038DI-1 IC REG BUCK SYNC ADJ 6A 8DFN
AOZ1038PI IC REG BUCK SYNC ADJ 6A 8SOIC
相关代理商/技术参数
参数描述
AMIS30623C623BRG 功能描述:马达/运动/点火控制器和驱动器 LIN STEPPER DRIVER STALL RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
AMIS-30623PGA 制造商:ON Semiconductor 功能描述:STEPPER MOTOR CNTRLR - Rail/Tube 制造商:ON Semiconductor 功能描述:STEPPER MOTOR CNTRLR - Tape and Reel
AMIS-30623PNA 制造商:ON Semiconductor 功能描述:STEPPER MOTOR CNTRLR - Trays 制造商:ON Semiconductor 功能描述:STEPPER MOTOR CNTRLR - Tape and Reel
AMIS-30624 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:I2C Micro-stepping Motor Driver
AMIS30624C6244G 功能描述:马达/运动/点火控制器和驱动器 I2C 800mA STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube