- 您现在的位置：买卖IC网 > PDF目录10533 > AMIS30663CANG2G (ON Semiconductor)TRANSCEIVER CAN HS 3.3V 8-SOIC PDF资料下载
参数资料
| 型号： | AMIS30663CANG2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 6/11页 |
| 文件大小： | 0K |
| 描述： | TRANSCEIVER CAN HS 3.3V 8-SOIC |
| 标准包装： | 96 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | CAN |
| 电源电压： | 4.75 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 管件 |
| 产品目录页面： | 1115 (CN2011-ZH PDF) |
| 其它名称： | 766-1015 |
AMIS30663
http://onsemi.com
4
Functional Description
General
The AMIS30663 is the interface between the CAN
protocol controller and the physical bus. It is intended for
use in automotive and industrial applications requiring baud
rates up to 1 Mbaud. It provides differential transmit
capability to the bus and differential receiver capability to
the CAN protocol controller. It is fully compatible to the
“ISO 118982” standard.
Operating Modes
AMIS30663 only operates in highspeed mode as
illustrated in Table 4.
The transceiver is able to communicate via the bus lines.
The signals are transmitted and received to the CAN
controller via the pins TxD and RxD. The slopes on the bus
lines outputs are optimised to give extremely low EME.
Table 4. Function Table (X = don’t care)
Mode
Pin
Bus
TxD
RxD
State
CANH
CANL
4.75 V < Vcc < 5.25 V
High
Speed
0
Dominant
High
Low
1
Recessive
0.5 Vcc
Vcc < PORL
X
1
Recessive
0 < VCANH < VCC
0 < VCANL < VCC
PORL < Vcc < 4.75 V
> VIH
1
Recessive
0 < VCANH < VCC
0 < VCANL < VCC
Overtemperature Detection
A thermal protection circuit protects the IC from damage
by switching off the transmitter if the junction temperature
exceeds a value of approximately 160
°C. Because the
transmitter dissipates most of the power, the power
dissipation and temperature of the IC is reduced. All other
IC functions continue to operate. The transmitter offstate
resets when pin TxD goes HIGH. The thermal protection
circuit is particularly needed when a bus line short circuits.
TxD Dominant Timeout Function
A TxD dominant timeout timer circuit prevents the bus
lines from being driven to a permanent dominant state
(blocking all network communication) if pin TxD is forced
permanently LOW by a hardware and/or software
application failure. The timer is triggered by a negative edge
on pin TxD. If the duration of the LOWlevel on pin TxD
exceeds the internal timer value tdom, the transmitter is
disabled, driving the bus into a recessive state. The timer is
reset by a positive edge on pin TxD.
Failsafe Features
A currentlimiting circuit protects the transmitter output
stage from damage caused by accidental shortcircuit to
either positive or negative supply voltage although power
dissipation increases during this fault condition.
The pins CANH and CANL are protected from
automotive electrical transients (according to “ISO 7637”;
see Figure 4).
Should TxD become disconnected, this pin is pulled high
internally.
When the Vcc supply is removed, pins TxD and RxD will
be floating. This prevents the AMIS30663 from being
supplied by the CAN controller through the I/O pins.
3.3 V Interface
AMIS30663 may be used to interface with 3.3 V or 5 V
controllers by use of the V33 pin. This pin may be supplied
with 3.3 V or 5 V to have the corresponding digital interface
voltage levels.
When the V33 pin is supplied at 2.5 V, even interfacing
with 2.5 V CAN controllers is possible. See also Digital
a pull resistor from TxD to V33 is necessary.
Electrical Characteristics
Definitions
All voltages are referenced to GND (pin 2). Positive
currents flow into the IC. Sinking current means that the
current is flowing into the pin. Sourcing current means that
the current is flowing out of the pin.
Absolute Maximum Ratings
Stresses above those listed in Table 5 may cause
permanent device failure. Exposure to absolute maximum
ratings for extended periods may effect device reliability.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B4T-MX-F2 | CONVERTER MOD DC/DC 6.5V 75W |
| EXP-0921/05/S | CONN RCPT 5POS IP68 W/SOCKETS |
| LTC1415CG#PBF | IC A/D CONV 12BIT SAMPLNG 28SSOP |
| AMIS30660CANH2G | TRANSCEIVER CAN HS 5V 8-SOIC |
| VE-J3Y-MY-F2 | CONVERTER MOD DC/DC 3.3V 33W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AMIS30663CANG2RG | 功能描述:CAN 接口集成电路 HS CAN TRANSC 3.3V RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| AMIS30663NGA | 制造商:AMI 制造商全称:AMI 功能描述:High Speed CAN Transceiver |
| AMIS-39100 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Octal High Side Driver with Protection |
| AMIS39100AGA | 制造商:AMI 制造商全称:AMI 功能描述:Octal High Side Driver with Protection |
| AMIS39100PNPB3G | 功能描述:功率驱动器IC OCTAL HS DRVR 12V RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。