- 您现在的位置：买卖IC网 > PDF目录378403 > AN-242 (National Semiconductor Corporation) LJT 18C 18#20 SKT RECP PDF资料下载
参数资料
| 型号： | AN-242 |
| 厂商： | National Semiconductor Corporation |
| 英文描述： | LJT 18C 18#20 SKT RECP |
| 中文描述： | 应用新的精密运算放大器 |
| 文件页数： | 1/16页 |
| 文件大小： | 267K |
| 代理商： | AN-242 |
TL/H/7479
A
A
National Semiconductor
Application Note 242
April 1980
Applying a New
Precision Op Amp
Robert J. Widlar
Apartado Postal 541
Puerto Vallarta, Jalisco
Mexico
Bob Pease and Mineo Yamatake
National Semiconductor Corporation
Santa Clara, California
U.S.A.
Abstract
: A new bipolar op amp design has advanced the
state of the art by reducing offset voltage and bias current
errors. Its characteristics are described here, indicating an
ultimate input resolution of 10
m
V and 1 pA under laboratory
conditions. Practical circuits for making voltmeters, amme-
ters, differential instrumentation amplifiers and a variety of
other designs that can benefit from the improved perform-
ance are covered in detail. Methods of coupling the new
device to existing fast amplifiers to take advantage of the
best characteristics of both, even in follower applications,
are explored.
introduction
A low cost, mass-produced op amp with electrometer-type
input currents combined with low offset voltage and drift is
now available. Designated the LM11, this IC can minimize
production problems by providing accuracy without adjust-
ments, even in high-impedance circuitry. On the other hand,
if pushed to its full potential, what has been impossible in
the past becomes entirely practical.
Significantly, the LM11 is not restricted to commercial and
industrial use. Devices can be completely specified over a
b
55
§
C to
a
125
§
C range. Preliminary data indicates that
reliability is the same as standard ICs qualified for military
and space applications.
The essential details of the design along with an introduc-
tion to the peculiarities of high-impedance circuits have
been presented elsewhere.
*
This will be expanded here.
Practical circuitry that reduces effective bias current for
those applications where performance cannot be made de-
pendent on offset current are described. In addition, circuits
combining the DC characteristics of the new part with the
AC performance of existing fast amplifiers will be shown.
This will be capped with a number of practical designs to
provide some perspective into what might be done.
dc errors
Barring the use of chopper or reset stabilization, the best
offset voltage, drift and long-term stability are obtained us-
ing bipolar transistors for the op amp input stage. This has
been done with the LM11. On-wafer trimming further im-
proves performance. Typically, a 100
m
V offset with
1
m
V/
§
C drift results.
Transistors with typical current gains of 5000 have been
used in the manufacture of the LM11. The input stage em-
ploys a Darlington connection that has been modified so
that offset voltage and drift are not degraded. The typical
input currents, plotted inFigure 1, demonstrate the value of
the approach.
TL/H/7479–1
Figure 1. Below 100
§
C, bias current varies almost linear-
ly with temperature. This means that simple
circuitry can be used for compensation. Offset
current is unusually low.
The offset current of this op amp is so low that it cannot be
measured on existing production test equipment. Therefore,
it probably cannot be specified tighter than 10 pA. For crit-
ical applications, the user should have little difficulty in se-
lecting to a tighter limit.
The bias current of the LM11 equals that of monolithic FET
amplifier at 25
§
C. Unlike FETs, it does not double every
10
§
C. In fact, the drift over a
b
55
§
C to
a
125
§
C temperature
range is about the same as that of a FET op amp during
normal warm up.
Other characteristics are summarized in Table I. It can be
seen that the common-mode rejection, supply-voltage re-
jection and voltage gain are high enough to take full advan-
tage of the low offset voltage. The unspectacular 0.3V/
m
s
slew rate is balanced by the 300
m
A current drain.
*
R. J. Widlar, ‘‘Working with High Impedance Op Amps’’, National Semiconductor AN-241.
C
1995 National Semiconductor Corporation
RRD-B30M115/Printed in U. S. A.
相关PDF资料 |
PDF描述 |
|---|---|
| AN-40 | Application Note 40 |
| AN-5002 | LJT 18C 18#20 SKT WALL RECP |
| AN-5025 | Applications Using the GTLP10B320 |
| AN-5026 | Circular Connector; No. of Contacts:19; Series:MS27656; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:15; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:15-19 RoHS Compliant: No |
| AN-5031 | GTLP Power Configuration |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AN24-22 | 制造商:AN# - MILITARY 功能描述: |
| AN24-31A | 制造商:AN# - MILITARY 功能描述: |
| AN2440 | 制造商:Distributed By MCM 功能描述:USB to DVI Adapter |
| AN2441S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Color Encoder Circuit |
| AN245 | 制造商:Panasonic Industrial Company 功能描述:IC |
发布紧急采购，3分钟左右您将得到回复。