- 您现在的位置：买卖IC网 > PDF目录378403 > AN-CC1002 (WINBOND ELECTRONICS CORP) Design Considerations for ISD1700 Family PDF资料下载
参数资料
| 型号： | AN-CC1002 |
| 厂商： | WINBOND ELECTRONICS CORP |
| 英文描述： | Design Considerations for ISD1700 Family |
| 中文描述： | 设计注意事项ISD1700系列 |
| 文件页数： | 1/3页 |
| 文件大小： | 138K |
| 代理商： | AN-CC1002 |
January, 2006
Page 1 / 3
Design Considerations for ISD1700 Family
AN-CC1002
1. Introduction
Winbond’s ISD1700 family is another ChipCorder
product, which has a Class D PWM
speaker output with wide operating voltage, ranging from 2.4V to 5.5V. This PWM
speaker driver maximizes audio volume and power efficiency. However, without
adequate system power supply and distribution design, can result in higher noise levels
than a typical speaker driver. Also, as usual, higher operating voltage induces more
power noise on the system. As a result, it increases the challenges on optimizing the
voice quality on an end-product.
This Application Note discusses the crucial factors for considerations while implementing
ISD1700 Series. Then, proposes some simple and cost-effective recommendations.
2. Decoupling Capacitors
In addition to the typical 0.1
μ
F capacitor on the power lines, when a 10
μ
F Aluminum
Electrolytic capacitor is added to each V
CCA
, V
CCD
and V
CCP
power line with respect to the
related ground path, it can reduce the noise from the power supplies. The locations of
these capacitors should be as close to the device as possible. By doing so, it enhances
the voice quality. Sometimes, a 4.7
μ
F Aluminum Electrolytic capacitor may be sufficient
for certain applications. Furthermore, we have experienced that the SMT capacitor
reduces the noise, but the result may not be as good as that using the Aluminum
Electrolytic type.
3. Layout Techniques
A good practice is to separate each power line (V
CCA
, V
CCD
& V
CCP
) and each ground path
(V
SSA
, V
SSD,
V
SSP1 &
V
SSP2
) individually from the device to the system. Meanwhile, the
ISD1700 device has isolated V
CCP,
V
SSP1
& V
SSP2
pads for PWM speaker driver. To
minimize the noise from the PWM speaker driver, it is vital to route an independent trace
from each related pin to the supply and ground terminals directly. The following aspects
should be taken into accounts:
Place V
SSA
and V
SSD
planes/paths on one side of PCB and the V
SSP1
& V
SSP2
planes/paths on the opposite side of PCB.
Make each V
SSA
and
V
SSD
as one big ground plane and as large as possible. Size
the V
SSA
and
V
SSD
planes in approximate equivalent area.
Layout the V
SSP1
& V
SSP2
traces as large as possible and connect them to the
system ground in the shortest distance.
Funnel each ground path back to ground terminal for better grounding effect.
Similarly, apply independent path technique on V
CCA
, V
CCD
and V
CCP
signals.
The decoupling capacitors should be as close to the device as possible.
相关PDF资料 |
PDF描述 |
|---|---|
| AN013 | JT 128C 128#22D SKT RECP |
| AN1025 | Converting A 5.0V Supply Rail To A Regulated 3.0V |
| AN1034 | Analog Switch and Multiplexer Applications |
| AN1042 | High Fidelity Switching Audio Amplifiers Using TMOS Power MOSFETs |
| AN1042D | High Fidelity Switching Audio Amplifiers Using TMOS Power MOSFETs |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ANCC-151A | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:PCS and WLAN Omni Antennas |
| ANCC-152A | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:PCS and WLAN Omni Antennas |
| ANCC-153A | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:PCS and WLAN Omni Antennas |
| ANCC-154A | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:PCS and WLAN Omni Antennas |
| ANCC-155A | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:PCS and WLAN Omni Antennas |
发布紧急采购，3分钟左右您将得到回复。