参数资料
型号: AN1593
厂商: Motorola, Inc.
元件分类: 基准电压源/电流源
英文描述: LOW COST 1.0 A CURRENT SOURCE FOR BATTERY CHARGERS
中文描述: 低成本1.0电流源的电池充电器
文件页数: 1/8页
文件大小: 212K
代理商: AN1593
Prepared by: Ondrej Pauk
Industrial System Application Laboratory
Roznov, CZ
Figure 1. Low Cost Current Source for Battery Chargers Demonstration Board
This paper describes two designs of low cost current
sources for battery charger applications based on the
LM2575–ADJ switching step–down converter and the
MC33341 regulator control circuit.
INTRODUCTION
This design is a highly cost effective 1.0 A current source
for battery chargers with a rectangular constant–current,
constant–voltage charging characteristic. This feature
assures a basic protection against overcharge whose results
can range from minor damage to catastrophic failure of the
whole system.
This circuit was designed to implement additional charge
control based either on the microcontroller or on any other
charging control unit in the system that operates from NiCd or
NiMH batteries. The MC33341 and this board may be used in
a wide variety of applications. All functions needed are
performed by just two integrated circuits and a small number
of external components. This allows a very compact printed
circuit board design and a very cost effective solution.
The LM2575–ADJ Easy Switch
step down converter
allows the system to operate from 8.0 to 40 Vdc, thus
allowing direct operation from both 12 and 24 V board
voltages used in the automotive industry. In comparison with
linear topologies of battery chargers, this circuit provides
much better efficiency, especially over a wide input voltage
range.
General Description
Today’s most popular rechargeable battery type is NiCd.
When overcharged, this type of battery experiences
increasing pressure inside the cell. This can cause opening
of the cell’s vent and release of oxygen. This has a
detrimental affect on the battery, although it may still retain
some useful capacity. When NiMH batteries are
overcharged, they also increase their internal pressure and
release some hydrogen, an extremely explosive gas.
The schematic diagram is shown in Figure 2. It is a 1.0 A
(maximum) “dumb” battery charger that uses the
LM2575–ADJ switching converter to step down the input dc
voltage, together with the MC33341, which regulates the
charging current flowing into the battery. The switching
regulator has high efficiency over a wide input voltage range,
which allows this design to be universal. Both 12 and 24 V car
batteries as well as cheap, poorly regulated, wall adaptors
can be used.
The term “dumb” battery charger means that it offers only
some basic protective features and the main protective and
control functions are maintained by a
μ
P based main control
unit inside the PC or the control function of a cellular phone.
This concept allows a very compact and cost effective
design.
Various charge techniques have to be used to
accommodate both NiCd and NiMH type batteries. Both NiCd
and NiMH batteries can be charged at a high current rate
Order this document by AN1593/D
Motorola, Inc. 1997
相关PDF资料
PDF描述
AN1607 ITC122 low voltage micro to motor interface
AN1672 The ECL Translator Guide
AN1672D The ECL Translator Guide
AN1687 A FULL-FEATURED WIRELESS INTERFACE FOR RS-232 COMMUNICATIONS
AN1812 Freescale Semiconductor, Inc.
相关代理商/技术参数
参数描述
AN15931A-E1 制造商:Panasonic Industrial Company 功能描述:IC
AN15-C08 制造商:SMC Corporation of America 功能描述:Silencer, Compact Resin, One-Touch, 8mm Port, 30 dB(A), 45mm, Model AN15-C08 制造商:SMC 功能描述:Compact silencer Resin 8mm push in male 制造商:SMC 功能描述:SY3000 silencer, compact resin type ()
AN15-N02 制造商:SMC Corporation of America 功能描述:Silencer, Airline, 1/4NPT Port
AN-16 制造商:未知厂家 制造商全称:未知厂家 功能描述:TOPSwitch Flyback Design Methodology
AN1603-433 制造商:未知厂家 制造商全称:未知厂家 功能描述:陶瓷天线 Multilayer Chip Antenna for 433MHz Wireless Communication