- 您现在的位置：买卖IC网 > PDF目录17067 > AP2172SG-13 (Diodes Inc)IC PWR SWITCH DUAL USB 1A 8-SOIC PDF资料下载
参数资料
| 型号： | AP2172SG-13 |
| 厂商： | Diodes Inc |
| 文件页数： | 13/17页 |
| 文件大小： | 0K |
| 描述： | IC PWR SWITCH DUAL USB 1A 8-SOIC |
| 产品变化通告： | Copper Bond Wire Change 13/Jan/2012 |
| 标准包装： | 1 |
| 类型： | USB 开关 |
| 输出数： | 2 |
| Rds（开）： | 160 毫欧 |
| 内部开关： | 是 |
| 电流限制： | 1.5A |
| 输入电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOP |
| 包装： | 标准包装 |
| 产品目录页面： | 1137 (CN2011-ZH PDF) |
| 其它名称： | AP2172SGDIDKR |
AP2162/AP2172
1A DUAL CHANNEL CURRENT-LIMITED POWER
SWITCH
Application Note
Power Supply Considerations
A 0.01- μ F to 0.1- μ F X7R or X5R ceramic bypass capacitor between IN and GND, close to the device, is
recommended. Placing a high-value electrolytic capacitor on the input and output pin(s) is recommended
when the output load is heavy. This precaution reduces power-supply transients that may cause ringing on
the input. Additionally, bypassing the output with a 0.01- μ F to 0.1- μ F ceramic capacitor improves the
immunity of the device to short-circuit transients.
Over-current and Short Circuit Protection
An internal sensing FET is employed to check for over-current conditions. Unlike current-sense resistors,
sense FETs do not increase the series resistance of the current path. When an overcurrent condition is
detected, the device maintains a constant output current and reduces the output voltage accordingly.
Complete shutdown occurs only if the fault stays long enough to activate thermal limiting.
Three possible overload conditions can occur. In the first condition, the output has been shorted to
GND before the device is enabled or before V IN has been applied. The AP2162/AP2172 senses the short
circuit and immediately clamps output current to a certain safe level namely I LIMIT .
In the second condition, an output short or an overload occurs while the device is enabled. At the instance
the overload occurs, higher current may flow for a very short period of time before the current limit function
can react. After the current limit function has tripped (reached the over-current trip threshold), the device
switches into current limiting mode and the current is clamped at I LIMIT .
In the third condition, the load has been gradually increased beyond the recommended operating current.
The current is permitted to rise until the current-limit threshold (I TRIG ) is reached or until the thermal limit of
the device is exceeded. The AP2162/AP2172 is capable of delivering current up to the current-limit threshold
without damaging the device. Once the threshold has been reached, the device switches into its current
limiting mode and is set at I LIMIT .
FLG Response
When an over-current or over-temperature shutdown condition is encountered, the FLG open-drain output
goes active low after a nominal 7-ms deglitch timeout. The FLG output remains low until both over-current
and over-temperature conditions are removed. Connecting a heavy capacitive load to the output of the
device can cause a momentary over-current condition, which does not trigger the FLG due to the 7-ms
deglitch timeout. The AP2162/AP2172 is designed to eliminate false over-current reporting without the need
of external components to remove unwanted pulses.
Power Dissipation and Junction Temperature
The low on-resistance of the internal MOSFET allows the small surface-mount packages to pass large
current. Using the maximum operating ambient temperature (T A ) and R DS(ON) , the power dissipation can be
calculated by:
P D = R DS(ON) × I 2
Finally, calculate the junction temperature:
T J = P D x R θ JA + T A
Where:
T A = Ambient temperature ° C
R θ JA = Thermal resistance
P D = Total power dissipation
AP2162/AP2172 Rev. 5
13 of 17
FEBRUARY 2009
? Diodes Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2005-0.8LYM5 TR | IC DISTRIBUTION SW 0.8A SOT23-5 |
| GBC08DREN-S93 | CONN EDGECARD 16POS .100 EYELET |
| RCA18DTKN | CONN EDGECARD 36POS DIP .125 SLD |
| GCM25DCSD | CONN EDGECARD 50POS DIP .156 SLD |
| RP40-4815DGW/N | CONV DC/DC 40W 18-75VIN +/-15V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP2176 | 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:1A DUAL CHANNEL CURRENT-LIMITED POWER SWITCH |
| AP2176MPG-13 | 功能描述:电源开关 IC - USB INTRFCE EN ACTIVE HI DUAL CHN 1A 2.7-5.5V RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| AP2176SG-13 | 功能描述:电源开关 IC - USB INTRFCE EN ACTIVE HI DUAL CHN 1A 2.7-5.5V RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| AP2181 | 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:1.5A SINGLE CHANNEL CURRENT-LIMITED POWER |
| AP2181_0906 | 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:1.5A SINGLE CHANNEL CURRENT-LIMITED POWER |
发布紧急采购，3分钟左右您将得到回复。