- 您现在的位置：买卖IC网 > PDF目录97843 > AP603-F 800 MHz - 2200 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER PDF资料下载
参数资料
| 型号： | AP603-F |
| 元件分类： | 放大器 |
| 英文描述： | 800 MHz - 2200 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| 封装： | 6 X 5 MM, ROHS COMPLIANT, MO-229VJGC, SMT, DFN-14 |
| 文件页数： | 8/14页 |
| 文件大小： | 1200K |
| 代理商： | AP603-F |
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com Web site: www.wj.com, www.TriQuint.com
Page 3 of 14 May 2007 ver 1
AP603
High Dynamic Range 7W 28V HBT Amplifier
Application Circuit PC Board Layout
PCB Material: 0.0147” Rogers Ultralam 2000, single layer, 1 oz Cu,
εr = 2.45, Microstrip line details: width = .042”, spacing = .050”
Baseplate Configuration
Notes:
1. Please note that for reliable operation, the evaluation board will have to be mounted to a much larger
heat sink during operation and in laboratory environments to dissipate the power consumed by the
device. The use of a convection fan is also recommended in laboratory environments.
2. The area around the module underneath the PCB should not contain any soldermask in order to
maintain good RF grounding.
3. For proper and safe operation in the laboratory, the power-on sequencing is recommended.
Evaluation Board Bias Procedure
The following bias procedure is recommended to ensure proper functionality of AP603 in a laboratory environment. The sequencing is not
required in the final system application.
Bias.
Voltage (V)
Vcc
+28
Vbias
+5
Vpd
+5
Turn-on Sequence:
1.
Attach input and output loads onto the evaluation board.
2.
Turn on power supply Vcc = +28V.
3.
Turn on power supply Vbias = +5V. At this point, the only current drawn by the device is leakage current (< 25μA).
4.
Turn on power supply Vpd = +5V. Power supply Vcc should now be drawing typical Icq = 160mA.
5.
Turn on RF power.
Turn-off Sequence:
1.
Turn off RF power.
2.
Turn off power supply Vpd = +5V.
3.
Turn off power supply Vbias = +5V.
4.
Turn off power supply Vcc = +28V.
Notes:
1.
Icq can be adjusted with the resistor R2 from the Vpd (+5V) supply and the PIN_VPD (pin14) of the amplifier. Increasing R2
results in a lower Icq. Icq should not be increased above 320mA.
2.
Vpd is used as a reference for the internal active bias circuitry. It can be used to turn on/off the amplifier. Ipd depends on the Icq
quiescent current setting. Ipd can be up to 8mA at a quiescent current setting of 320mA.
3.
Vbias should be maintained fixed at +5V. Ibias will change based on RF input power level. It can be up to 8mA on the AP603.
Ipd vs Icq
0
2
4
6
8
0
100
200
300
400
Icq Setting (mA)
Ipd
(
m
A
)
Ibias vs Output Power
0
2
4
6
8
22
24
26
28
30
32
Output Average Power (dBm)
Ib
ia
s
(
m
A
)
相关PDF资料 |
PDF描述 |
|---|---|
| APS3605RS26Q1 | 50 MHz - 1000 MHz RF/MICROWAVE SPLITTER |
| AR6270B | BASE STATION/BROADCAST TRANSMISSION ANTENNA |
| ARA1400IS12CTR | RF/MICROWAVE NARROW BAND HIGH POWER AMPLIFIER |
| ARA1400IS12C | RF/MICROWAVE NARROW BAND HIGH POWER AMPLIFIER |
| ARA2000S12 | RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP603-PCB1960 | 功能描述:射频开发工具 1930-1990MHz Brd 12dB Gain RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| AP603-PCB2140 | 功能描述:射频开发工具 2110-2170MHz Brd 12dB Gain RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| AP603-PCB900 | 功能描述:射频开发工具 869-960MHz Eval Brd 17dB Gain RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| AP604A-F | 功能描述:射频放大器 AMP. 15W. 28V HBT RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| AP6050R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:PSU BENCH AUTO RANGE 1000W |
发布紧急采购，3分钟左右您将得到回复。