- 您现在的位置：买卖IC网 > PDF目录166228 > APW7066QAC-TRL (ANPEC ELECTRONICS CORP) Dual Synchronous Buck PWM Controllers and One Linear Controller PDF资料下载
参数资料
| 型号： | APW7066QAC-TRL |
| 厂商： | ANPEC ELECTRONICS CORP |
| 元件分类： | 稳压器 |
| 英文描述： | Dual Synchronous Buck PWM Controllers and One Linear Controller |
| 中文描述： | SWITCHING CONTROLLER, QCC32 |
| 封装： | 5 X 5 MM, LEAD FREE, QFN-32 |
| 文件页数： | 33/33页 |
| 文件大小： | 338K |
| 代理商： | APW7066QAC-TRL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页
Copyright
ANPEC Electronics Corp.
Rev. A.7 - Mar., 2008
APW7066
9
Function Pin Description
VCC
Power supply input pin. Connect a nominal 5V power
supply to this pin for the control circuit, or connect a
resistor (nominally 300
) to VCC12 for a shunt
regulator function (typical 5.8V). It is recommended
that a decoupling capacitor (1 to 10uF) is connected
to the GND for noise decoupling.
GND
This pin is the signal ground pin. The metal thermal
pad under the package is the IC substrate; connects
the GND pin and metal thermal pad together on the
board, and ties to the good GND plane for electrical
and thermal conduction.
VCC12
Power supply input pin. Connect a nominal 12V power
supply to this pin for the gate driver. It is recommended
that a decoupling capacitor (1 to 10uF) is connected
to the GND for noise decoupling.
PGND
This pin is the power ground pin for the gate driver and
linear driver circuit. It should be tied to the GND.
FB1, FB2, FB3
These pins are the inverting inputs of the error ampli-
fiers of their respective regulators. They are used to
set the output voltage and the compensation
components.
SS1/EN1, SS2/EN2, SS3/EN3
These pins provide two functions. Connect a capacitor
to the GND for setting the soft-start time. Use an open
drain logic signal to pull the SS/EN pin low to disable
the respective output, leave open to enable the re-
spective output.
COMP1, COMP2
These pins are the outputs of error amplifiers of their
respective regulators. They are used to set the
compensation components.
UGATE1, UGATE2
These pins provide the gate driver for the upper
MOSFETs of VOUT1 and VOUT2.
LGATE1, LGATE2
These pins provide the gate driver for the lower
MOSFETs of VOUT1 and VOUT2.
BOOT1, BOOT2
These pins provide the bootstrap voltage to the gate
driver for driving the upper MOSFETs. It can be
connected to a power voltage directly, but the differ-
ence voltage between the BOOT and VIN must be high
enough to drive the upper MOSFETs.
REFIN
This pin is the reference input voltage of error amplifier
of the VOUT2. It also provides the voltage into a buffer,
which is out on the REFOUT pin.
REFOUT
This pin provides a buffed voltage, which is from REFIN
pin. In Independent mode, it can be used by other
ICs. In DDR mode, it is from the VOUT1, and can be
used as the VTT buffer.
This pin also uses to select the phase shift (see table1).
When this pin pulls to VCC, the buffer is disabled and
the REFOUT is not available for use. It is recommended
that a 0.1uF capacitor is connected to the ground for
stability.
VREF
This pin provides a 3.3V reference voltage, which can
be used by the REFIN pin or other ICs as a voltage
reference. It is recommended that a 1uF capacitor is
connected to ground for stability.
DRIVE3
This pin drives the gate of an external N-channel
MOSFET for linear regulator.
PGOOD
This pin is an open drain device; connect a pull up
resistor to the VCC for PGOOD function.
FS/SYNC
This pin is used to adjust the switching frequency.
Connecting a resistor from FS/SYNC pin to the ground
increases the switching frequency. Conversely, con-
necting a resistor from this pin to the VCC12 reduces
the switching frequency. In addition, this pin also
provides synchronous frequency function. An external
clock can be fed into this pin, and force the switching
frequency to follow the external clock.
相关PDF资料 |
PDF描述 |
|---|---|
| AQ1058N2J-T | 1 ELEMENT, 0.0082 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| AQ1053N3S-T | 1 ELEMENT, 0.0033 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| AQ1052N2S-T | 1 ELEMENT, 0.0022 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| AQ10512NJ-T | 1 ELEMENT, 0.012 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| AQ1059N1J-T | 1 ELEMENT, 0.0091 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| APW7066QAC-TU | 制造商:ANPEC 制造商全称:Anpec Electronics Coropration 功能描述:Dual Synchronous Buck PWM Controllers and One Linear Controller |
| APW7066QAC-TUL | 制造商:ANPEC 制造商全称:Anpec Electronics Coropration 功能描述:Dual Synchronous Buck PWM Controllers and One Linear Controller |
| APW7066RC-TR | 制造商:ANPEC 制造商全称:Anpec Electronics Coropration 功能描述:Dual Synchronous Buck PWM Controllers and One Linear Controller |
| APW7066RC-TRG | 制造商:ANPEC 制造商全称:Anpec Electronics Coropration 功能描述:Dual Synchronous Buck PWM Controllers and One Linear Controller |
| APW7066RC-TRL | 制造商:ANPEC 制造商全称:Anpec Electronics Coropration 功能描述:Dual Synchronous Buck PWM Controllers and One Linear Controller |
发布紧急采购，3分钟左右您将得到回复。