- 您现在的位置：买卖IC网 > PDF目录20255 > AS1100WL-T (ams)IC LED 8-DIGIT DRIVER 24-SOIC PDF资料下载
参数资料
| 型号： | AS1100WL-T |
| 厂商： | ams |
| 文件页数： | 7/17页 |
| 文件大小： | 0K |
| 描述： | IC LED 8-DIGIT DRIVER 24-SOIC |
| 标准包装： | 1 |
| 显示器类型： | LED |
| 配置： | 7 段 + DP |
| 接口： | 串行 |
| 数字或字符： | 8 位数字 |
| 电流 - 电源： | 330mA |
| 电源电压： | 4 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC |
| 包装： | 标准包装 |
| 产品目录页面： | 804 (CN2011-ZH PDF) |
| 其它名称： | AS1100WL-TDKR |
AS1100
Datasheet - D e t a i l e d D e s c r i p t i o n
8 Detailed Description
8.1 Serial-Addressing Modes
Programming of the AS1100 is done via 4 wire serial interface. A programming sequence consists of 16-bit packages. The data is shifted into the
internal 16 Bit register with the rising edge of the CLK signal. With the rising edge of the LOAD signal the data is latched into a digital or control
register depending on the address. The LOAD signal must go to high after the 16th rising clock edge. The LOAD signal can also come later but
just before the next rising edge of CLK, otherwise data would be lost. The content of the internal shift register is applied 16.5 clock cycles later to
the DOUT pin. The data is clocked out at the falling edge of CLK. The Bits of the 16Bit-programming package are described in Table 5 . The first
4 Bits D15-D12 are don’t care, D11-D8 contain the address and D7-D0 contain the data. The first bit is D15, the most significant bit (MSB). The
Figure 5. Timing Diagram
LOAD
t CSW
t CL
t CH
t CP
t CS
t LDCK
CLK
t DH
t DS
DIN
D15
D14
D1
D0
t DO
DOUT
Table 4. Serial Data Format (16bits)
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
Address
MSB
Data
LSB
8.2 Digit and Control Registers
The AS1100 incorporates 15 registers, which are listed in Table 5 . The digit and control registers are selected via the 4Bit address word. The 8
digit registers are realized with a 64bit memory. Each digit can be controlled directly without rewriting the whole contents. The control registers
consist of decode mode, display intensity, number of scanned digits, shutdown, display test, and reset/external clock register.
8.3 Shutdown Mode
The AS1100 features a shutdown mode, where it consumes only 20 A current. The shutdown mode is entered via a write to register 0Ch. Then
all segment current sources are pulled to ground and all digit drivers are connected to V DD , so that nothing is displayed. All internal digit
registers keep the programmed values. The shutdown mode can either be used for power saving or for generating a flashing display by
repeatedly entering and leaving the shutdown mode. The AS1100 needs typically 250 s to exit the shutdown mode. During shutdown the
AS1100 is fully programmable. Only the display test function overrides the shutdown mode.
8.4 Initial Power-Up
After powering up the system all register are reset, so that the display is blank. The AS1100 starts the shutdown mode. All registers should be
programmed for normal operation. The default settings enable only scan of one digit, the internal decoder is disabled, data register and intensity
register are set to the minimum value.
www.austriamicrosystems.com/LED-Driver-ICs/AS1100
Revision 1.37
6 - 16
相关PDF资料 |
PDF描述 |
|---|---|
| R0.25S12-0512/H | CONV DC/DC 0.25W 5V IN 12V OUT |
| PSA15R-075PV-R-C3 | ADAPTER WALL R-SERIES 15W 7.5V |
| V375B28C300B | CONVERTER MOD DC/DC 28V 300W |
| VE-J2H-CX-B1 | CONVERTER MOD DC/DC 52V 75W |
| R0.25S12-0509/P | CONV DC/DC 0.25W 5V IN 9V OUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1100WL-TZ | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:Serially Interfaced, 8-Digit LED Driver |
| AS1100WL-Z | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:Serially Interfaced, 8-Digit LED Driver |
| AS1101 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:Low-Dropout LED Drivers |
| AS1101_1 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:Low-Dropout LED Drivers |
| AS11010 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。