- 您现在的位置：买卖IC网 > PDF目录20255 > AS1100WL-T (ams)IC LED 8-DIGIT DRIVER 24-SOIC PDF资料下载
参数资料
| 型号： | AS1100WL-T |
| 厂商： | ams |
| 文件页数： | 8/17页 |
| 文件大小： | 0K |
| 描述： | IC LED 8-DIGIT DRIVER 24-SOIC |
| 标准包装： | 1 |
| 显示器类型： | LED |
| 配置： | 7 段 + DP |
| 接口： | 串行 |
| 数字或字符： | 8 位数字 |
| 电流 - 电源： | 330mA |
| 电源电压： | 4 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC |
| 包装： | 标准包装 |
| 产品目录页面： | 804 (CN2011-ZH PDF) |
| 其它名称： | AS1100WL-TDKR |
AS1100
Datasheet - D e t a i l e d D e s c r i p t i o n
8.5 Decode-Mode Register
In the AS1100 a BCD decoder is included. Every digit can be selected via register 09h to be decoded. The BCD code consists of the numbers 0-
9, E,H, L,P and -. In register 09h a logic high enables the decoder for the appropriate digit. In case that the decoder is bypassed (logic low) the
data Bits D7-D0 correspond to the segment lines of the AS1100. In Table 7 some possible settings for register 09h are shown. Bit D7, which
corresponds to the decimal point, is not affected by the settings of the decoder. Logic high means that the decimal point is displayed. In Table 8
the font of the Code B decoder is shown. In Table 9 the correspondence of the register to the appropriate segments of a 7 segment display is
8.6 Intensity Control and Interdigit Blanking
Brightness of the display can be controlled in an analog way by changing the external resistor (R SET ). The current, which flows between V DD
and ISET, defines the current that flows through the LEDs. The LED current is 100 times the ISET current. The minimum value of R SET should
be 9.53k ? , which corresponds to 40mA segment current. The brightness of the display can also be controlled digitally via register 0Ah. The
brightness can be programmed in 16 steps and is shown in Table 10 . An internal pulse width modulator controls the intensity of the display.
8.7 Scan-Limit Register
The scan limit register 0Bh selects the number of digits displayed. When all 8 digits are displayed the update frequency is typically 800Hz. If the
number of digits displayed is reduced, the update frequency is reduced as well. The frequency can be calculated using 8fOSC/N, where N is the
number of digits. Since the number of displayed digits influences the brightness, the resistor R SET should be adjusted accordingly. The Table 12
shows the maximum allowed current, when fewer than 4 digits are used. To avoid differences in brightness the scan limit register should not be
used to blank portions of the display (leading zeros).
Table 5. Register Address Map
Register
No-Op
Digit 0
Digit 1
Digit 2
Digit 3
Digit 4
Digit 5
Digit 6
Digit 7
Decode Mode
Intensity
Scan Limit
Shutdown
Not used
Reset and ext. Clock
Display Test
D15-D12
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
D11
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
Address
D10
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
D9
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
D8
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Hex
Code
0xX0
0xX1
0xX2
0xX3
0xX4
0xX5
0xX6
0xX7
0xX8
0xX9
0xXA
0xXB
0xXC
0xXD
0xXE
0xXF
Table 6. Shutdown Register Format (address (hex) = 0xXC
Mode
Address Code
(Hex)
D7
D6
D5
Register Data
D4 D3
D2
D1
D0
Shutdown Mode
Normal Operation
0xXC
0xXC
X
X
X
X
X
X
X
X
X
X
X
X
X
X
0
1
www.austriamicrosystems.com/LED-Driver-ICs/AS1100
Revision 1.37
7 - 16
相关PDF资料 |
PDF描述 |
|---|---|
| R0.25S12-0512/H | CONV DC/DC 0.25W 5V IN 12V OUT |
| PSA15R-075PV-R-C3 | ADAPTER WALL R-SERIES 15W 7.5V |
| V375B28C300B | CONVERTER MOD DC/DC 28V 300W |
| VE-J2H-CX-B1 | CONVERTER MOD DC/DC 52V 75W |
| R0.25S12-0509/P | CONV DC/DC 0.25W 5V IN 9V OUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1100WL-TZ | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:Serially Interfaced, 8-Digit LED Driver |
| AS1100WL-Z | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:Serially Interfaced, 8-Digit LED Driver |
| AS1101 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:Low-Dropout LED Drivers |
| AS1101_1 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:Low-Dropout LED Drivers |
| AS11010 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。