参数资料
| 型号： | AS1108PL |
| 厂商： | ams |
| 文件页数： | 10/21页 |
| 文件大小： | 0K |
| 描述： | IC LED 4-DIGIT DRIVER 20-PDIP |
| 标准包装： | 18 |
| 显示器类型： | LED |
| 配置： | 7 段 + DP |
| 接口： | 串行 |
| 数字或字符： | 4 位数字 |
| 电流 - 电源： | 330mA |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 20-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 20-PDIP |
| 包装： | 管件 |
AS1108
Datasheet - D e t a i l e d D e s c r i p t i o n
Shutdown Mode
The AS1108 features a shutdown mode, consuming only 10μA (max) current. Shutdown mode is entered via a write to
the Shutdown Register (see Table 8). At that point, all segment current sources are pulled to ground and all digit driv-
ers are connected to V DD , so that all segments are blanked.
Note: During shutdown mode the Digit-Registers maintain their data.
Shutdown mode can either be used as a means to reduce power consumption or for generating a flashing display
(repeatedly entering and leaving shutdown mode). For minimum supply current in shutdown mode, logic input should
be at GND or V DD (CMOS logic level).
The device needs typically 250μs to exit shutdown mode, and during shutdown mode the AS1108 is fully programma-
ble. Only the display test mode (see page 11) overrides shutdown mode.
When entering or leaving shutdown mode, the Feature Register is reset to its default values (all 0s) when Shutdown
Register bit D7 (page 10) = 0. When bit D7 = 1, the Feature Register is left unchanged when entering or leaving shut-
down mode.
Note: If the AS1108 is used with an external clock, Shutdown Register bit D7 should be set to 1 when writing to the
Shutdown Register.
Digit- and Control-Registers
The AS1108 contains four Digit-Registers and six control-registers, which are listed in Table 7. All registers are
selected using a 4-bit address word, and communication is done via the serial interface.
Digit Registers – These registers are realized with an on-chip 32-bit memory. Each digit can be controlled directly
without rewriting the whole register contents.
Control Registers – These registers consist of decode mode, display intensity, number of scanned digits, shut-
down, display test and features selection registers.
Table 7. Register Address Map
Register
No-Op
Digit 0
Digit 1
Digit 2
Digit 3
Decode-Mode
Intensity Control
Scan Limit
Shutdown
N/A
Feature
Display Test
HEX Code
0xX0
0xX1
0xX2
0xX3
0xX4
0xX9
0xXA
0xXB
0xXC
0xXD
0xXE
0xXF
D15:D12
X
X
X
X
X
X
X
X
X
X
X
X
D11
0
0
0
0
0
1
1
1
1
1
1
1
Address
D10
0
0
0
0
1
0
0
0
1
1
1
1
D9
0
0
1
1
0
0
1
1
0
0
1
1
D8
0
1
0
1
0
1
0
1
0
1
0
1
Page
N/A
N/A
N/A
N/A
N/A
Revision 2.13
9 - 20
相关PDF资料 |
PDF描述 |
|---|---|
| AS1119-BWLT | IC LED 144CH DRIVER 36WLCSP |
| AS1302-BWLT | IC REG BST SWITCHD CAP 5V 8WLCSP |
| AS1310-BTDT-18 | IC REG BOOST 1.8V 60MA 8TDFN |
| AS1322A-BTTT | IC REG BOOST SYNC ADJ TSOT23-6 |
| AS1323-BTTT-30 | IC REG BST SYNC 3V 0.1A TSOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1108WL | 功能描述:IC LED 4-DIGIT DRIVER 20-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 显示器驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 显示器类型:真空荧光 (VF) 配置:5 x 7（矩阵） 接口:串行 数字或字符:- 电流 - 电源:3.5mA 电源电压:2.7 V ~ 3.6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 供应商设备封装:16-QSOP 包装:带卷 (TR) |
| AS1108-WL | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| AS1108WL-T | 功能描述:IC DRIVER LED 4-DIGIT 20-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 显示器驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 显示器类型:真空荧光 (VF) 配置:5 x 7（矩阵） 接口:串行 数字或字符:- 电流 - 电源:3.5mA 电源电压:2.7 V ~ 3.6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 供应商设备封装:16-QSOP 包装:带卷 (TR) |
| AS1108WL-T-Z | 制造商:AMS 功能描述:0 |
| AS1108-XXX-I-A1-D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
发布紧急采购，3分钟左右您将得到回复。