参数资料
| 型号： | AS1108PL |
| 厂商： | ams |
| 文件页数： | 9/21页 |
| 文件大小： | 0K |
| 描述： | IC LED 4-DIGIT DRIVER 20-PDIP |
| 标准包装： | 18 |
| 显示器类型： | LED |
| 配置： | 7 段 + DP |
| 接口： | 串行 |
| 数字或字符： | 4 位数字 |
| 电流 - 电源： | 330mA |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 20-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 20-PDIP |
| 包装： | 管件 |
AS1108
Datasheet - D e t a i l e d D e s c r i p t i o n
8 Detailed Description
Serial-Addressing Format
Programming the AS1108 is accomplished by writing to the device’s internal registers (see Digit- and Control-Registers
on page 9) via the 4-wire serial interface. A programming sequence consists of 16-bit packages as depicted in Table 6.
The data is shifted into the internal 16-bit register with the rising edge of the CLK signal. With the rising edge of the
LOAD/CSN signal the data is latched into a digit- or control-register. The LOAD/CSN signal must go high after the 16th
rising clock edge.
The LOAD/CSN signal can also come later but this must happen just before the next rising edge of CLK, otherwise the
data will be lost. The contents of the internal shift register are applied 16.5 clock cycles later to pin DOUT. The data is
clocked out at the falling edge of CLK.
The first 4 bits (D15:D12) are “don't care” settings, bits D11:D8 contain the register address, and bits D7:D0 contain the
Table 6. 16-Bit Serial Data Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
Register Address (see Table 7) MSB
Data
LSB
Initial Power-Up
On initial power-up, the AS1108 registers are reset to their default values, the display is blanked, and the device goes
into shutdown mode. All registers should be programmed for normal operation at this time.
Note: The default settings enable only scanning of one digit; the internal decoder is disabled and the Intensity Control
Register (see page 12) is set to the minimum values.
Figure 10. Interface Timing
LOAD/
CSN
t CSH
t CSW
t CSS
t CL
t CH
t CP
t LDCK
CLK
t DS
t DH
DIN
D15
D14
D1
D0
t DO
DOUT
Revision 2.13
8 - 20
相关PDF资料 |
PDF描述 |
|---|---|
| AS1119-BWLT | IC LED 144CH DRIVER 36WLCSP |
| AS1302-BWLT | IC REG BST SWITCHD CAP 5V 8WLCSP |
| AS1310-BTDT-18 | IC REG BOOST 1.8V 60MA 8TDFN |
| AS1322A-BTTT | IC REG BOOST SYNC ADJ TSOT23-6 |
| AS1323-BTTT-30 | IC REG BST SYNC 3V 0.1A TSOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1108WL | 功能描述:IC LED 4-DIGIT DRIVER 20-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 显示器驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 显示器类型:真空荧光 (VF) 配置:5 x 7（矩阵） 接口:串行 数字或字符:- 电流 - 电源:3.5mA 电源电压:2.7 V ~ 3.6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 供应商设备封装:16-QSOP 包装:带卷 (TR) |
| AS1108-WL | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| AS1108WL-T | 功能描述:IC DRIVER LED 4-DIGIT 20-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 显示器驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 显示器类型:真空荧光 (VF) 配置:5 x 7（矩阵） 接口:串行 数字或字符:- 电流 - 电源:3.5mA 电源电压:2.7 V ~ 3.6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 供应商设备封装:16-QSOP 包装:带卷 (TR) |
| AS1108WL-T-Z | 制造商:AMS 功能描述:0 |
| AS1108-XXX-I-A1-D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
发布紧急采购，3分钟左右您将得到回复。