- 您现在的位置：买卖IC网 > PDF目录20251 > AS1115-BQFT (ams)IC DVR LED 64LED/7SEG I2C 24UQFN PDF资料下载
参数资料
| 型号： | AS1115-BQFT |
| 厂商： | ams |
| 文件页数： | 10/26页 |
| 文件大小： | 0K |
| 描述： | IC DVR LED 64LED/7SEG I2C 24UQFN |
| 产品培训模块： | AS1115 Overview |
| 标准包装： | 1 |
| 显示器类型： | LED |
| 配置： | 8 x（7 段），64 LED |
| 接口： | I²C |
| 数字或字符： | 8 位数字 |
| 电流 - 电源： | 335mA |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-UFQFN 裸露焊盘 |
| 供应商设备封装： | 24-TQFN（4x4） |
| 包装： | 标准包装 |
| 其它名称： | AS1115-BQFTDKR |
AS1115
Datasheet - D e t a i l e d D e s c r i p t i o n
I2C Interface
The AS1115 supports the I2C serial bus and data transmission protocol in high-speed mode at 3.4MHz. The AS1115 operates as a slave on the
I2C bus. The bus must be controlled by a master device that generates the serial clock (SCL), controls the bus access, and generates the START
and STOP conditions. Connections to the bus are made via the open-drain I/O pins SCL and SDA.
Figure 18. I2C Interface Initialization
1
8
9
1
8
9
0
0
0
0
0
A1
A0 R/W
D15 D14 D13 D12 D11 D10
D9
D8
Default values at power up: A1 = A0 = 0
Figure 19. Bus Protocol
SDI
MSB
Slave Address
R/W
Direction Bit
ACK from
Receiver
ACK from
Receiver
SCL
1
2
6
7
8
9
1
2
3-8
8
9
START
ACK
ACK
Repeat if More Bytes Transferred
STOP or
Repeated
START
The bus protocol (as shown in Figure 19 ) is defined as:
- Data transfer may be initiated only when the bus is not busy.
- During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in the data line while the clock line is
HIGH will be interpreted as control signals.
The bus conditions are defined as:
-
-
-
-
Bus Not Busy . Data and clock lines remain HIGH.
Start Data Transfer . A change in the state of the data line, from HIGH to LOW, while the clock is HIGH, defines a START condition.
Stop Data Transfe r. A change in the state of the data line, from LOW to HIGH, while the clock line is HIGH, defines the STOP condition.
Data Valid . The state of the data line represents valid data, when, after a START condition, the data line is stable for the duration of the
HIGH period of the clock signal. There is one clock pulse per bit of data.
Each data transfer is initiated with a START condition and terminated with a STOP condition. The number of data bytes transferred
between START and STOP conditions is not limited and is determined by the master device. The information is transferred byte-wise and
each receiver acknowledges with a ninth-bit.
Within the I2C bus specifications a high-speed mode (3.4MHz clock rate) is defined.
- Acknowledge : Each receiving device, when addressed, is obliged to generate an acknowledge after the reception of each byte. The mas-
ter device must generate an extra clock pulse that is associated with this acknowledge bit. A device that acknowledges must pull down the
SDA line during the acknowledge clock pulse in such a way that the SDA line is stable LOW during the HIGH period of the acknowledge
clock pulse. Of course, setup and hold times must be taken into account. A master must signal an end of data to the slave by not generat-
Revision 1.08
9 - 25
相关PDF资料 |
PDF描述 |
|---|---|
| VE-21L-EV-F1 | CONVERTER MOD DC/DC 28V 150W |
| ACM28DSEN-S243 | CONN EDGECARD 56POS .156 EYELET |
| VE-213-EV-F3 | CONVERTER MOD DC/DC 24V 150W |
| V375B36C300BF2 | CONVERTER MOD DC/DC 36V 300W |
| ABM28DSEN-S243 | CONN EDGECARD 56POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1115BSST | 制造商:ams 功能描述:T&R / QSOP 24pin |
| AS1115-BSST | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| AS1115-BSST-CUT TAPE | 制造商:AMS 功能描述:AS Series 5.5 V 3.4 MHz SMT I2C Interfaced LED Driver with Keyscan - QSOP-24 |
| AS1115DB | 制造商:AMS 功能描述:0 |
| AS1115-DB-Blue | 制造商:ams 功能描述:AS1115 Demo Brd w/blue LEDs |
发布紧急采购，3分钟左右您将得到回复。