- 您现在的位置：买卖IC网 > PDF目录14774 > AS1322B-BTTT (ams)IC REG BOOST SYNC ADJ TSOT23-6 PDF资料下载
参数资料
| 型号： | AS1322B-BTTT |
| 厂商： | ams |
| 文件页数： | 12/18页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC ADJ TSOT23-6 |
| 设计资源： | Design Support Tool |
| 标准包装： | 1 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.5 V ~ 5 V |
| 输入电压： | 0.65 V ~ 5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.2MHz |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 细型，TSOT-23-6 |
| 包装： | 标准包装 |
| 供应商设备封装： | TSOT-23-6 |
| 其它名称： | AS1322B-BTTTDKR |
AS1322
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
9.2 External Component Selection
Inductor Selection
The fast switching frequency (1.2MHz) of the AS1322 allows for the use of small surface mount or chip inductor for the external inductor (see
Figure 15 on page 7) .
The required minimum values for the external inductor are:
3.3μH for applications ≤ 3.6V
4.7μH for applications > 3.6V
Larger inductor values allow greater output current capability by reducing the inductor ripple current. Increasing the inductance above 10μH will
increase size while providing negligible improvement in output current capability.
The approximate output current capability of the AS1322 versus inductor value is given in:
I OUT ( MAX ) = η ? ? I P – ------------------ ? ? ( 1 – D )
f ? L ? 2 ?
?
V IN ? D
(EQ 2)
Where:
η is the estimated efficiency;
I P is the peak current limit value (0.6A);
V IN is the input voltage;
D is the steady-state duty ratio = (V OUT - V IN )/V OUT ;
f is the switching frequency (1.2MHz typ);
L is the inductor value.
The inductor current ripple is typically set for 20 to 40% of the maximum inductor current (I P ). High-frequency ferrite core inductor materials
reduce frequency dependent power losses compared to less expensive powdered iron types, which result in improved converter efficiency.
2
The inductor should have low ESR to reduce the I R power losses, and must be able to handle the peak inductor current without saturating.
Molded chokes and some chip inductors normally do not have enough core to support the peak inductor currents of the AS1322 (850mA typ). To
minimize radiated noise, use a toroid, pot core, or shielded bobbin inductor.
Table 5. Recommended Inductors
Part Number
MOS6020-103ML
MOS6020-472ML
MOS6020-332ML
CDRH4D18-100
CDRH4D18-6R8
CR43-6R8
CDRH4D18-4R7
L
10μH
4.7μH
3.3μH
10μH
6.8μH
6.8μH
4.7μH
DCR
93m ?
50m ?
46m ?
200m ?
200m ?
131.2m ?
162m ?
Current Rating
1A
1.5A
1.8A
0.61A
0.76A
0.95A
0.84A
Dimensions (L/W/T)
6.8x6.0x2.4mm
6.8x6.0x2.4mm
6.8x6.0x2.4mm
6.9x5.0x2.0mm
6.9x5.0x2.0mm
4.8x4.3x3.5mm
6.9x5.0x2.0mm
Coilcraft
www.coilcraft.com
Sumida
www.sumida.com
www.ams.com/DC-DC_Step-Up/AS1322
Revision 1.10
12 - 18
相关PDF资料 |
PDF描述 |
|---|---|
| RCA40DTKN | CONN EDGECARD 80POS DIP .125 SLD |
| MAX6461XR22+T | IC VOLT DETECTOR LP SC70-3 |
| V110B15T150B3 | CONVERTER MOD DC/DC 15V 150W |
| V110B15T150B | CONVERTER MOD DC/DC 15V 150W |
| MAX6461XR29+T | IC VOLT DETECTOR LP SC70-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1322-EB | 制造商:ams 功能描述:AS1322 Evaluation Board |
| AS1-322-W3-302 | 制造商:TE Connectivity 功能描述: |
| AS1323 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:1.6uA Quiescent Current, Single Cell, DC-DC Step-up Converter |
| AS1323_04 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:1.6??A Quiescent Current, Single Cell, DC-DC Step-up Converter |
| AS1323_1 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:1.6uA Quiescent Current, Single Cell, DC-DC Step-up Converter |
发布紧急采购，3分钟左右您将得到回复。