- 您现在的位置：买卖IC网 > PDF目录14447 > AS1326B-BTDR (ams)IC REG BST SYNC 3.3V/ADJ 10TDFN PDF资料下载
参数资料
| 型号： | AS1326B-BTDR |
| 厂商： | ams |
| 文件页数： | 14/19页 |
| 文件大小： | 0K |
| 描述： | IC REG BST SYNC 3.3V/ADJ 10TDFN |
| 标准包装： | 624 |
| 类型： | 升压（升压） |
| 输出类型： | 两者兼有 |
| 输出数： | 1 |
| 输出电压： | 3.3V，2.5 V ~ 5 V |
| 输入电压： | 0.7 V ~ 5 V |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 800mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 托盘 |
| 供应商设备封装： | 10-TDFN（3x3） |
| 产品目录页面： | 804 (CN2011-ZH PDF) |
AS1326
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
Inductor Selection
The AS1326A/AS1326B high switching-frequency allows the use of a small 3.3μH surface-mount inductor. The induc-
tor should generally have a saturation current rating exceeding the N-channel switch current limit; however, it is
acceptable to bias the inductor current into saturation by as much as 20% if a slight reduction in efficiency is accept-
able.
Lower current-rated inductors may be used if ISET is used to reduce the peak inductor current (see Setting the Switch
Current Limit on page 12) . For high efficiency, select an inductor with a high-frequency ferrite core material to reduce
core losses. To minimize radiated noise, use a toroid or shielded inductor. Connect the inductor from the battery to the
pin LX as close to the device as possible.
Table 7. Recommended Inductors
Part Number
L
DCR
Current Rating Dimensions (L/W/T)
Manufacturer
MOS6020-332
LPS4018-332
DO1608C-272
CDRH5D18NP-4R1N
3.3μH
3.3μH
2.7μH
4.1μH
46m Ω
80m Ω
80m Ω
57m Ω
1.8A
2.0A
2.1A
1.95A
6.8x6.0x2.4mm
4x4x1.8mm
6.6x4.45x2.92mm
6x6x2mm
Coilcraft
Sumida
Figure 23. Efficiency vs. I OUT ; V IN = 2V, V OUT = 3.3V
96
94
92
90
88
86
84
82
Figure 24. Efficiency vs. I OUT ; V IN = 3V, V OUT = 5V
96
94
92
90
88
86
84
82
80
78
80
78
76
MOS6020-332
DO1608C-272
CDRH5D18NP-4R1N
LPS4018-332
76
74
72
70
MOS6020-332
DO1608C-272
CDRH5D18NP-4R1N
LPS4018-332
0.1
1
10
100
1000
0.1
1
10
100
1000
Output Current (mA)
Output Current (mA)
External Schottky Diode
For output voltages greater than 4V, an external Schottky diode must be connected between pin LX and POUT, in par-
allel with the integrated synchronous rectifier (see Figure 25) . The diode should be rated for 0.5A. An external diode is
also recommended for applications that must start with input voltages at or below 1.8V. The Schottky diode carries cur-
rent during startup and after the synchronous rectifier turns off; thus, its current rating only needs to be 500mA.
Note: Connect the diode as close to the IC as possible.
For circuits that do not require startup with inputs below 1.8V and have an output of 4V or less, the external
diode is not needed.
Caution: Do not use ordinary rectifier diodes as their slow switching speeds and long reverse-recovery times render
them unacceptable.
www.austriamicrosystems.com
Revision 1.05
13 - 18
相关PDF资料 |
PDF描述 |
|---|---|
| LPX681M350H4P3 | CAP ALUM 680UF 350V 20% SNAP |
| RMA10DTBN | CONN EDGECARD 20POS R/A .125 SLD |
| WBR30-250A | CAP ALUM 30UF 250V AXIAL |
| RBA24DTBN | CONN EDGECARD 48POS R/A .125 SLD |
| LGN2P182MELC50 | CAP ALUM 1800UF 220V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1326BBTDT | 制造商:ams 功能描述:IC STEP-UP DC/DC CONVERTER TDFN-10 制造商:ams 功能描述:T&R / TDFN 3x3 10 |
| AS1326B-BTDT | 功能描述:IC REG BST SYNC 3.3V/ADJ 10TDFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:50 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:5 V ~ 25 V 输入电压:2.3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:600kHz，1.2MHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 包装:管件 供应商设备封装:8-MSOP |
| AS1326-EB | 制造商:ams 功能描述:AS1326 Evaluation Board |
| AS1328A-BQFT-12 | 功能描述:IC REG BUCK SYNC 1.2V 3A 16-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:50 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:5 V ~ 25 V 输入电压:2.3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:600kHz，1.2MHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 包装:管件 供应商设备封装:8-MSOP |
| AS1328A-BQFT-15 | 功能描述:IC REG BUCK SYNC 1.5V 3A 16-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:50 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:5 V ~ 25 V 输入电压:2.3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:600kHz，1.2MHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 包装:管件 供应商设备封装:8-MSOP |
发布紧急采购，3分钟左右您将得到回复。