- 您现在的位置：买卖IC网 > PDF目录14724 > AS1341-BTDT-1K (ams)IC REG BUCK 5V/ADJ 0.6A 8TDFN PDF资料下载
参数资料
| 型号： | AS1341-BTDT-1K |
| 厂商： | ams |
| 文件页数： | 11/18页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 5V/ADJ 0.6A 8TDFN |
| 设计资源： | Design Support Tool |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 两者兼有 |
| 输出数： | 1 |
| 输出电压： | 5V，1.25 V ~ 20 V |
| 输入电压： | 4.5 V ~ 20 V |
| 频率 - 开关： | 200kHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WDFN 裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-TDFN（3x3） |
| 其它名称： | AS1341-BTDT-1KDKR |
AS1341
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
9.3 Setting Current Limit
The AS1341 adjustable peak current limit is set by connecting ILIMIT as shown in Table 4 .
Table 4. Setting Peak Current Limit
Current Limit
700mA
1400mA
ILIMIT Connected To
GND
IN
The current limit chosen should reflect the maximum load current. The maximum output current is half of the peak current limit. Choosing a lower
current limit allows using an inductor with a lower current rating, however, it requires a higher inductance (see Inductor Selection) and does not
allow for reduced inductor package size.
9.4 Inductor Selection
The AS1341 operates with a wide range of inductance values. For most applications, values between 10μH and 47μH work best with the
controller ’s high switching frequency. Larger inductor values will reduce the switching frequency and thereby improve efficiency and EMI.
Note: The four key factors in inductor selection are inductance value, saturation rating, series resistance, and size.
The trade-off for improved efficiency is a higher output ripple and slower transient response. On the other hand, low-value inductors respond
faster to transients, improve output ripple, offer smaller physical size, and minimize cost. If the inductor value is too small, the peak inductor
current exceeds the current limit due to current-sense comparator propagation delay, potentially exceeding the inductor ’s current rating.
Calculate the minimum inductance value as follows:
L MIN = ((V INMAX - V OUTPUT ) x t ONMIN /I LXPEAK
(EQ 3)
Where:
t ONMIN = 1μs
The inductor saturation current rating must be greater than the peak switch current limit, plus the overshoot due to the 250ns current-sense
comparator propagation delay. Saturation occurs when the magnetic flux density of the inductor reaches the maximum level the core can support
and the inductance starts to fall. Choose an inductor with a saturation rating greater than IPEAK in the following equation:
I PEAK = (I LXPEAK + (V IN - V OUTPUT ) x 250ns)/L
(EQ 4)
Inductor series resistance affects both efficiency and dropout voltage (see Dropout Voltage on page 9) . High series resistance limits the
maximum current available at lower input voltages, and increases the dropout voltage. For optimum performance, select an inductor with the
lowest possible DC resistance that fits in the allotted dimensions.
Table 5. Recommended Inductors
Part Number
MSS6132-103ML
LPS4018-472ML
MSS6132-393ML
LPS4018-223ML
CDRH6D28NP-150
CDRH5D18NP-4R1
CDRH6D28NP-470
CDRH5D18NP-220
LQH66SN-100M03
LQH55DN-150M03
LQH66SN-470M03
LQH55DN-470M03
www.ams.com/DC-DC_Step-Up/AS1341
L
10μH
4.7μH
39μH
22μH
15μH
4.1μH
47μH
22μH
10μH
15μH
47μH
47μH
DCR
85m ?
125m ?
345m ?
360m ?
62m ?
57m ?
176m ?
215m ?
36m ?
150m ?
170m ?
400m ?
Revision 1.09
Current Rating
1.4A
1.8A
0.8A
0.7A
1.4A
1.95A
0.8A
0.8A
1.6A
1.4A
0.8A
0.8A
Coilcraft
www.coilcraft.com
Sumida
www.sumida.com
Murata
www.murata.com
11 - 18
相关PDF资料 |
PDF描述 |
|---|---|
| RCM40DCCS | CONN EDGECARD 80POS R/A .156 SLD |
| EB81-S0C1560W | CONN EDGEBOARD DUAL 30POS 5A |
| RBM25DCBT | CONN EDGECARD 50POS R/A .156 SLD |
| GBM40DTKI-S288 | CONN EDGECARD 80POS .156 EXTEND |
| RCM40DCBS | CONN EDGECARD 80POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1341-BTDT-6K | 功能描述:IC REG BUCK 5V/ADJ 0.6A 8TDFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:50 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:5 V ~ 25 V 输入电压:2.3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:600kHz，1.2MHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 包装:管件 供应商设备封装:8-MSOP |
| AS1341-CUT TAPE | 制造商:AMS 功能描述:AS Series 20 V 600 mA Surface Mount 100% Duty Cycle Step-Down Converter - TDFN-8 |
| AS1341-EB | 制造商:ams 功能描述:AS1341 Evaluation Board |
| AS1341-TD_EK_ST | 功能描述:AS1341 - DC/DC, Step Down with LDO 1, Non-Isolated Outputs Evaluation Board 制造商:ams 系列:- 零件状态:有效 主要用途:DC/DC，LDO 步降 输出和类型:1，非隔离 功率 - 输出:- 电压 - 输出:3.3V 电流 - 输出:600mA 电压 - 输入:4.5 V ~ 20 V 稳压器拓扑:降压 频率 - 开关:200kHz 板类型:完全填充 所含物品:板 使用的 IC/零件:AS1341 标准包装:1 |
| AS1343 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:42V, 1-2 Cells, Micropower, DC-DC Boost Converter |
发布紧急采购，3分钟左右您将得到回复。