参数资料
型号: AS3648-ZWLT
厂商: ams
文件页数: 15/39页
文件大小: 0K
描述: IC LED DVR 2000MA FLASH 13WLCSP
标准包装: 10,000
恒定电压:
拓扑: PWM,升压(升压)
输出数: 2
内部驱动器:
类型 - 主要: 闪灯/白光
频率: 4MHz
电源电压: 2.7 V ~ 4.4 V
输出电压: 2.8 V ~ 5.5 V
安装类型: 表面贴装
封装/外壳: 13-UFBGA,WLCSP
供应商设备封装: 13-WLCSP(2.25x1.5)
包装: 带卷 (TR)
工作温度: -30°C ~ 85°C
AS3648
Datasheet, Confidential - D e t a i l e d D e s c r i p t i o n
Table 5. Operating Mode and current settings (Continued)
AS3648 configuration
operating mode and currents
setting out_on
(see
page
26)
mode_
(see
page
27)
Condition
Mode
LED_OUT1/2
output current
X
X
10, 01
or 11
0
X
0
X
X
ext_torch_on (see page
23) not 10
ext_torch_on =10
standby
0
by the 7LSB bits of
low current pwm mode
by the 7LSB bits (6...0)
1
X
X
X
X
X
00
01
10
X
1
1
ext_torch_on =10
external torch mode
indicator mode or
assist light mode
3
LED current is defined
2
led_current1 and
led_current2
LED current is defined
by the 6LSB bits (bits
5...0) of led_current1
and led_current2 pwm
modulated with
31.25kHz defined by
register inct_pwm (1/
16...4/16)
LED current is defined
2
of led_current1 and
led_current2
X
X
strobe_on (see page 27)
=0
flash mode;
X
X
0->1
1
11
1
strobe_on = 1 and
strobe_type (see page
27) = 0
strobe_on = 1 and
strobe_type = 1
flash duration defined by
flash_timeout (see page
26)
flash mode;
flash duration defined by
STROBE input; timeout
defined by flash_timeout
LED current is defined
by led_current1 and
led_current2 - the
current can be reduced
during flash, see Flash
Current Reductions
below
1. SCL low for t TIMEOUT and operating mode is indicator, assist or flash mode then shutdown mode is entered.
2. The MSB bit of this register not used to protect the LED; therefore the maximum assist / torch light current = half
the maximum flash current
3. The low current mode is a general purpose PWM mode to drive less current through the LED in average, but
keep the actual pulsed current in a range where the light output from the LED is still specified. As only the 6
LSBs of led_current1 and led_current2 are used the maximum current is limited to 1/4 of the maximum flash
current.
Flash Current Reductions
TXMASK
Usually the flash current is defined by the register led_current1 and led_current2 . If the TXMASK/TORCH input is used
and (configured by ext_torch_on =01), the flash current is reduced to flash_txmask_current if TXMASK/TORCH=1.
Current Reduction by VIN measurements in Flash Mode
Due to the high load of the flash driver and the ESR of the battery (especially critical at low temperatures), the voltage
on the battery drops. If the voltage drops below the reset threshold of the system would reset. To prevent this condition
the AS3648 monitors the battery voltage and keeps it above vin_low_v_run as follows:
www.austriamicrosystems.com/AS3648
1.5-4
14 - 38
相关PDF资料
PDF描述
P51-500-S-T-I12-4.5V-000-000 SENSOR 500PSI 7/16-20-2B .5-4.5V
REC7.5-4815DRW/H2/A/M/CTRL CONV DC/DC 7.5W 36-72VIN +/-15V
REC3-243.3SRW/H2/C/M/SMD CONV DC/DC 3W 18-36VIN 3.3VOUT
P51-2000-S-S-I12-4.5V-000-000 SENSOR 2000PSI 1/4-18NPT .5-4.5V
P51-500-S-B-M12-4.5V-000-000 SENSOR 500PSI 1/8-27NPT .5-4.5V
相关代理商/技术参数
参数描述
AS3648-ZWLT-500 功能描述:IC WHITE LED FLASH DVR 13WLCSP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压(升压),切换式电容器(充电泵) 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽) 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C
AS36490FLF 制造商:TT Electronics / IRC 功能描述:AS36490FLF
AS36490HLF 制造商:TT Electronics / IRC 功能描述:AS36490HLF
AS36490JLF 制造商:TT Electronics / IRC 功能描述:AS36490JLF
AS36491FLF 制造商:TT Electronics / IRC 功能描述:AS36491FLF