- 您现在的位置：买卖IC网 > PDF目录21928 > AS5040-ASSU (ams)IC ENCODER PROG 10-BIT 16-SSOP PDF资料下载
参数资料
| 型号： | AS5040-ASSU |
| 厂商： | ams |
| 文件页数： | 12/34页 |
| 文件大小： | 0K |
| 描述： | IC ENCODER PROG 10-BIT 16-SSOP |
| 应用说明： | AS5000 Series Magnet Selection Guide AS5000 Series Magnets for Extended Vertical Range |
| 标准包装： | 77 |
| 传感范围： | 45mT ~ 75mT |
| 类型： | 线性，旋转编码器 - 可编程 |
| 电源电压： | 3 V ~ 3.6 V，4.5 V ~ 5.5 V |
| 电流 - 电源： | 21mA |
| 电流 - 输出（最大）： | 4mA |
| 输出类型： | 正交，带刻度角（增量） |
| 特点： | 可编程 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
AS5040
Data Sheet
Table 3: Magnetic Magnitude Variation Indicator
Mag
INCn
0
0
1
1
Mag
DECn
0
1
0
1
Description
No distance change; Magnetic input field OK (in range, 45..75mT)
Distance increase: Pull-function. This state is dynamic, it is only active while the magnet is
moving away from the chip in Z-axis
Distance decrease: Push- function. This state is dynamic, it is only active while the magnet is
moving towards the chip in Z.-axis.
Magnetic Input Field invalid – out of range: <45mT or >75mT (or missing magnet)
Note: Pins 1 and 2 (MagINCn, MagDECn) are open drain outputs and require external pull-up resistors. If the
magnetic field is in range, both outputs are turned off.
The two pins may also be combined with a single pull-up resistor. In this case, the signal is high when the magnetic
field is in range. It is low in all other cases (see Table 3).
Even Parity bit for transmission error detection of bits 1…15 (D9…D0, OCF, COF, LIN, MagINCn, MagDECn)
The absolute angular output is always set to a resolution of 10 bit. Placing the magnet above the chip, angular values
increase in clockwise direction by default.
Data D9:D0 is valid, when the status bits have the following configurations:
Table 4: Status Bit Outputs
OCF
1
COF
0
LIN
0
Mag
INCn
0
0
1
Mag
DECn
0
1
0
Parity
even checksum of bits
1:15
The absolute angular position is sampled at a rate of 10kHz (0.1ms). This allows reading of all 1024 positions per 360
degrees within 0.1 seconds = 9.76Hz (~10Hz) without skipping any position. Multiplying 10Hz by 60, results the
corresponding maximum rotational speed of 600 rpm.
Readout of every second angular position allows for rotational speeds of up to 1200rpm.
Consequently, increasing the rotational speed reduces the number of absolute angular positions per revolution (see
Table 7). Regardless of the rotational speed or the number of positions to be read out, the absolute angular value is
always given at the highest resolution of 10 bit.
The incremental outputs are not affected by rotational speed restrictions due to the implemented interpolator. The
incremental output signals may be used for high-speed applications with rotational speeds of up to 30,000 rpm without
missing pulses.
Daisy Chain Mode
The Daisy Chain mode allows connection of several AS5040’s in series, while still keeping just one digital input for
data transfer (see “Data IN” in Figure 6 below). This mode is accomplished by connecting the data output (DO; pin 9)
to the data input (Prog; pin 8) of the subsequent device. An RC filter must be implemented between each PROG pin
of device n and DO pin of device n+1, to prevent the encoders to enter the alignment mode, in case of ESD
discharge, long cables, or not conform signal levels or shape. Using the values R=100R and C=1nF allow a max. CLK
frequency of 1MHz on the whole chain. The serial data of all connected devices is read from the DO pin of the first
device in the chain. The Prog pin of the last device in the chain should be connected to VSS. The length of the serial
bit stream increases with every connected device, it is
n * (16+1) bits:
e.g. 34 bit for two devices, 51 bit for three devices, etc…
The last data bit of the first device (Parity) is followed by a logic low bit and the first data bit of the second device (D9),
etc… (see Figure 7).
www.austriamicrosystems.com
Revision 2.10
11 - 33
相关PDF资料 |
PDF描述 |
|---|---|
| AS5043-ASSU | IC ENCODER PROG 10-BIT 16-SSOP |
| NFL21SP207X1C3D | FILTER LC HIGH FREQ 22PF 0805 |
| AS5145A-HSST-500 | IC ENCODER ROTARY MAGN 16-SSOP |
| D2JW-01K11L | IMMERSION-PROOF BASIC SWITCH |
| NFL21SP157X1C3D | FILTER LC HIGH FREQ 28PF 0805 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5040DB | 制造商:ams 功能描述: |
| AS5040-DB-V2 | 功能描述:磁传感器开发工具 AS5040 Demo Board RoHS:否 制造商:Maxim Integrated 工具用于评估: 接口类型: 工作电压: |
| AS5040-PB | 功能描述:磁传感器开发工具 AS5040 Progamming Board RoHS:否 制造商:Maxim Integrated 工具用于评估: 接口类型: 工作电压: |
| AS5040-SS_EK_AB | 功能描述:AS5040 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:9V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5040 标准包装:1 |
| AS5040-SS_EK_DB | 功能描述:AS5040 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板，线缆 使用的 IC/零件:AS5040 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。