- 您现在的位置：买卖IC网 > PDF目录21928 > AS5040-ASSU (ams)IC ENCODER PROG 10-BIT 16-SSOP PDF资料下载
参数资料
| 型号： | AS5040-ASSU |
| 厂商： | ams |
| 文件页数： | 17/34页 |
| 文件大小： | 0K |
| 描述： | IC ENCODER PROG 10-BIT 16-SSOP |
| 应用说明： | AS5000 Series Magnet Selection Guide AS5000 Series Magnets for Extended Vertical Range |
| 标准包装： | 77 |
| 传感范围： | 45mT ~ 75mT |
| 类型： | 线性，旋转编码器 - 可编程 |
| 电源电压： | 3 V ~ 3.6 V，4.5 V ~ 5.5 V |
| 电流 - 电源： | 21mA |
| 电流 - 输出（最大）： | 4mA |
| 输出类型： | 正交，带刻度角（增量） |
| 特点： | 可编程 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
AS5040
Data Sheet
Figure 12: U, V and V-signals for BLDC Motor Commutation (Div1=0, Div0=0)
Commutation - Mode 3.0
Width: 512 Steps
U
V
W
CW Direction
(One-pole-pair)
Width: 512 Steps
Position:
Angle:
0
0.0
171
60.12
341
119.88
512
180.0
683
240.12
853
299.88
0
360.0
Figure 13: U, V and W-signals for 2-pole BLDC Motor Commutation (Div1=1; Div0=0)
Commutation - Mode 3.2
(Two-pole-pairs)
U
V
W
CW Direction
Width: 256 Steps
Width: 256 Steps
Position:
Angle:
0
0.0
85
29.88
171
60.12
256
90.0
341
119.88
427
150.12
512
180.0
597
209.88
683
240.12
768
270.00
853
299.88
939
330.12
0
360.0
12 Programming the AS5040
After power-on, programming the AS5040 is enabled with the rising edge of CSn with Prog = high and CLK = low. 16
bit configuration data must be serially shifted into the OTP register via the Prog-pin. The first “CCW” bit is followed by
the zero position data (MSB first) and the incremental mode setting as shown in Table 6. Data must be valid at the
rising edge of CLK (see Figure 14).
After writing data into the OTP register it can be permanently programmed by rising the Prog pin to the programming
voltage V PROG . 16 CLK pulses (t PROG ) must be applied to program the fuses (Figure 15). To exit the programming
mode, the chip must be reset by a power-on-reset. The programmed data is available after the next power-up.
Note: During the programming process, the transitions in the programming current may cause high voltage spikes
generated by the inductance of the connection cable. To avoid these spikes and possible damage to the IC, the
connection wires, especially the signals Prog and VSS must be kept as short as possible. The maximum wire length
between the V PROG switching transistor and pin Prog (see Figure 16) should not exceed 50mm (2 inches). To
suppress eventual voltage spikes, a 10nF ceramic capacitor should be connected close to pins Prog and VSS. This
capacitor is only required for programming, it is not required for normal operation.
The clock timing t clk must be selected at a proper rate to ensure that the signal Prog is stable at the rising edge of CLK
(see Figure 14). Additionally, the programming supply voltage should be buffered with a 10μF capacitor mounted
close to the switching transistor. This capacitor aids in providing peak currents during programming.
The specified programming voltage at pin Prog is 7.3 – 7.5V (see section 0). To compensate for the voltage drop
across the V PROG switching transistor, the applied programming voltage may be set slightly higher (7.5 - 8.0V, see
Figure 16).
www.austriamicrosystems.com
Revision 2.10
16 - 33
相关PDF资料 |
PDF描述 |
|---|---|
| AS5043-ASSU | IC ENCODER PROG 10-BIT 16-SSOP |
| NFL21SP207X1C3D | FILTER LC HIGH FREQ 22PF 0805 |
| AS5145A-HSST-500 | IC ENCODER ROTARY MAGN 16-SSOP |
| D2JW-01K11L | IMMERSION-PROOF BASIC SWITCH |
| NFL21SP157X1C3D | FILTER LC HIGH FREQ 28PF 0805 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5040DB | 制造商:ams 功能描述: |
| AS5040-DB-V2 | 功能描述:磁传感器开发工具 AS5040 Demo Board RoHS:否 制造商:Maxim Integrated 工具用于评估: 接口类型: 工作电压: |
| AS5040-PB | 功能描述:磁传感器开发工具 AS5040 Progamming Board RoHS:否 制造商:Maxim Integrated 工具用于评估: 接口类型: 工作电压: |
| AS5040-SS_EK_AB | 功能描述:AS5040 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:9V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5040 标准包装:1 |
| AS5040-SS_EK_DB | 功能描述:AS5040 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板，线缆 使用的 IC/零件:AS5040 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。