- 您现在的位置：买卖IC网 > PDF目录17275 > AS5045 DB V2 (ams)BOARD DEMO AS5045 PDF资料下载
参数资料
| 型号： | AS5045 DB V2 |
| 厂商： | ams |
| 文件页数： | 19/34页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO AS5045 |
| 标准包装： | 1 |
| 传感器类型： | 磁性，旋转位置 |
| 传感范围： | 360° |
| 接口： | USB |
| 电源电压： | 5V USB 或 9V |
| 嵌入式： | 是，MCU，8 位 |
| 已供物品： | 板 |
| 已用 IC / 零件： | AS5045 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
AS5045
Data Sheet
11 Programming the AS5045
After power-on, programming the AS5045 is enabled with the rising edge of CSn and Prog = logic high. 16 bit
configuration data must be serially shifted into the OTP register via the Prog pin. The first “CCW” bit is followed by
the zero position data (MSB first) and the Mode setting bits. Data must be valid at the rising edge of CLK (see
Figure 10 ).
After writing the data into the OTP register it can be permanently programmed by rising the Prog pin to the
programming voltage V PROG . 16 CLK pulses (t PROG ) must be applied to program the fuses ( Figure 11 ). To exit the
programming mode, the chip must be reset by a power-on-reset. The programmed data is available after the next
power-up.
Note: During the programming process, the transitions in the programming current may cause high voltage spikes
generated by the inductance of the connection cable. To avoid these spikes and possible damage to the IC, the
connection wires, especially the signals Prog and VSS must be kept as short as possible. The maximum wire length
between the V PROG switching transistor and pin Prog should not exceed 50mm (2 inches). To suppress eventual
voltage spikes, a 10nF ceramic capacitor should be connected close to pins VPROG and VSS. This capacitor is only
required for programming, it is not required for normal operation. The clock timing t clk must be selected at a proper
rate to ensure that the signal Prog is stable at the rising edge of CLK (see Figure 10 ). Additionally, the programming
supply voltage should be buffered with a 10μF capacitor mounted close to the switching transistor. This capacitor
aids in providing peak currents during programming. The specified programming voltage at pin Prog is 7.3 ~ 7.5V
(see section 6.8).
To compensate for the voltage drop across the V PROG switching transistor, the applied programming voltage may be
set slightly higher (7.5 ~ 8.0V, see Figure 12 ).
OTP Register Contents:
CCW
Z [11:0]:
PWM dis:
Counter Clockwise Bit
ccw=0 – angular value increases in clockwise direction
ccw=1 – angular value increases in counter clockwise direction
Programmable Zero Position
Disable PWM output
MagCompEn: When set, activates LIN alarm both when magnetic field is too high and too low (see Table 5 )
PWMhalfEn:
When set, PWM frequency is 122Hz or 2μs / step (when PWMhalfEN = 0, PWM frequency is 244Hz,
1μs / step)
11.1 Zero Position Programming
Zero position programming is an OTP option that simplifies assembly of a system, as the magnet does not need to
be manually adjusted to the mechanical zero position. Once the assembly is completed, the mechanical and
electrical zero positions can be matched by software. Any position within a full turn can be defined as the permanent
new zero position.
For zero position programming, the magnet is turned to the mechanical zero position (e.g. the “off”-position of a
rotary switch) and the actual angular value is read.
This value is written into the OTP register bits Z11:Z0 (see Figure 10 ) and programmed (see Figure 11 ).
Note: The zero position value may also be modified before programming, e.g. to program an electrical zero position
that is 180° (half turn) from the mechanical zero position, just add 2048 to the value read at the mechanical zero
position and program the new value into the OTP register.
11.2 Repeated OTP Programming
Although a single AS5045 OTP register bit can be programmed only once (from 0 to 1), it is possible to program
other, unprogrammed bits in subsequent programming cycles. However, a bit that has already been programmed
should not be programmed twice. Therefore it is recommended that bits that are already programmed are set to “0”
during a programming cycle.
www.austriamicrosystems.com
Revision 1.7
18 – 33
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17080EVKIT+ | KIT EVAL FOR MAX17080 |
| ECC20DCMD | CONN EDGECARD 40POS .100 WW |
| TDL825K020S1B | CAP TANT 8.2UF 20V 10% RADIAL |
| 100R28-76B | CABLE FLAT FLEX 28POS 1MM 3" |
| EBM15DRTH | CONN EDGECARD 30POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5045-EK-AB | 制造商:ams 功能描述:BOARD ADAPTER AS5045 |
| AS5045-SS_EK_AB | 功能描述:AS5045 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:9V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5045 标准包装:1 |
| AS5045-SS_EK_DB | 功能描述:AS5045 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板 使用的 IC/零件:AS5045 标准包装:1 |
| AS5045TR | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:12 BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER |
| AS5045-Z | 制造商:AMS 功能描述:0 |
发布紧急采购，3分钟左右您将得到回复。