- 您现在的位置：买卖IC网 > PDF目录17275 > AS5045 DB V2 (ams)BOARD DEMO AS5045 PDF资料下载
参数资料
| 型号： | AS5045 DB V2 |
| 厂商： | ams |
| 文件页数： | 21/34页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO AS5045 |
| 标准包装： | 1 |
| 传感器类型： | 磁性，旋转位置 |
| 传感范围： | 360° |
| 接口： | USB |
| 电源电压： | 5V USB 或 9V |
| 嵌入式： | 是，MCU，8 位 |
| 已供物品： | 板 |
| 已用 IC / 零件： | AS5045 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
Following the 18 clock (after reading bit “ccw”), the chip must be reset by disconnecting the power supply.
AS5045
Data Sheet
Figure 12. OTP Programming Connection of AS5045 (shown with AS5045 demoboard)
11.4 Analog Readback Mode
Non-volatile programming (OTP) uses on-chip zener diodes, which become permanently low resistive when
subjected to a specified reverse current.
The quality of the programming process depends on the amount of current that is applied during the programming
process (up to 130mA). This current must be provided by an external voltage source. If this voltage source cannot
provide adequate power, the zener diodes may not be programmed properly.
In order to verify the quality of the programmed bit, an analog level can be read for each zener diode, giving an
indication whether this particular bit was properly programmed or not.
To put the AS5045 in Analog Readback Mode, a digital sequence must be applied to pins CSn, PROG and CLK as
shown in Figure 13 . The digital level for this pin depends on the supply configuration (3.3V or 5V; see section 13
3V / 5V Operation).
The second rising edge on CSn (OutpEN) changes pin PROG to a digital output and the log. high signal at pin PROG
must be removed to avoid collision of outputs (grey area in Figure 13 ).
The following falling slope of CSn changes pin PROG to an analog output, providing a reference voltage V ref , that
must be saved as a reference for the calculation of the subsequent programmed and unprogrammed OTP bits.
Following this step, each rising slope of CLK outputs one bit of data in the reverse order as during programming
(see Figure 10 : Md0-MD1-Div0,Div1-Indx-Z0…Z11, ccw).
If a capacitor is connected to pin PROG, it should be removed during analog readback mode to allow a fast readout
rate. If the capacitor is not removed the analog voltage will take longer to stabilize due to the additional capacitance.
The measured analog voltage for each bit must be subtracted from the previously measured V ref , and the resulting
value gives an indication on the quality of the programmed bit: a reading of <100mV indicates a properly
programmed bit and a reading of >1V indicates a properly unprogrammed bit.
A reading between 100mV and 1V indicates a faulty bit, which may result in an undefined digital value, when the
OTP is read at power-up.
th
www.austriamicrosystems.com
Revision 1.7
20 – 33
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17080EVKIT+ | KIT EVAL FOR MAX17080 |
| ECC20DCMD | CONN EDGECARD 40POS .100 WW |
| TDL825K020S1B | CAP TANT 8.2UF 20V 10% RADIAL |
| 100R28-76B | CABLE FLAT FLEX 28POS 1MM 3" |
| EBM15DRTH | CONN EDGECARD 30POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5045-EK-AB | 制造商:ams 功能描述:BOARD ADAPTER AS5045 |
| AS5045-SS_EK_AB | 功能描述:AS5045 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:9V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5045 标准包装:1 |
| AS5045-SS_EK_DB | 功能描述:AS5045 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板 使用的 IC/零件:AS5045 标准包装:1 |
| AS5045TR | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:12 BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER |
| AS5045-Z | 制造商:AMS 功能描述:0 |
发布紧急采购，3分钟左右您将得到回复。