- 您现在的位置：买卖IC网 > PDF目录21914 > AS5163-HTSU (ams)IC ENCODER PROG 12-BIT 14TSSOP PDF资料下载
参数资料
| 型号： | AS5163-HTSU |
| 厂商： | ams |
| 文件页数： | 10/37页 |
| 文件大小： | 0K |
| 描述： | IC ENCODER PROG 12-BIT 14TSSOP |
| 应用说明： | AS5000 Series Magnet Selection Guide AS5000 Series Magnets for Extended Vertical Range |
| 特色产品： | AS5163 - Contactless Magnetic Angle Position Sensor |
| 标准包装： | 96 |
| 传感范围： | 30mT ~ 70mT |
| 类型： | 线性，旋转编码器 - 可编程 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 20mA |
| 输出类型： | 模拟，比率 |
| 特点： | 可编程 |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
AS5163
Datasheet - D e t a i l e d D e s c r i p t i o n
7.2 Analog Output
The reference voltage for the Digital-to-Analog converter (DAC) is taken internally from VDD . In this mode, the output voltage is ratiometric to the
supply voltage.
7.2.1
Programming Parameters
The Analog output voltage modes are programmable by OTP. Depending on the application, the analog output can be adjusted. The user can
program the following application specific parameters:
T1
T2
T1Y
T2Y
CLL
CLH
BP
Mechanical angle start point
Mechanical angle end point
Voltage level at the T1 position
Voltage level at the T2 position
Clamping Level Low
Clamping Level High
Break point (transition point 0 to 360 degree)
The above listed parameters are input parameters. Over the provided programming software and programmer, these parameters are converted
and finally written into the AS5163 128-bit OTP memory.
7.2.2
Application Specific Angular Range Programming
The application range can be selected by programming T1 with a related T1Y and T2 with a related T2Y into the AS5163. The internal gain factor
is calculated automatically. The clamping levels CLL and CLH can be programmed independent from the T1 and T2 position and both levels can
be separately adjusted.
Figure 5. Programming of an Individual Application Range
90 degree
Application range
electrical range
T2
T1
100%VDD
CLH
mechanical range
clamping range
high
180 degree
CLL
0 degree
T2Y
CLH
BP
T1Y
CLL
270 degree
0
clamping range
low
T1
T2
Figure 5 shows a simple example of the selection of the range. The mechanical starting point T1 and the mechanical end point T2 define the
mechanical range. A sub range of the internal Cordic output range is used and mapped to the needed output characteristic. The analog output
signal has 12 bit, hence the level T1Y and T2Y can be adjusted with this resolution. As a result of this level and the calculated slope the clamping
region low is defined. The break point BP defines the transition between CLL and CLH . In this example, the BP is set to 0 degree. The BP is also
the end point of the clamping level high CLH . This range is defined by the level CLH and the calculated slope. Both clamping levels can be set
independently form each other. The minimum application range is 10 degrees.
www.austriamicrosystems.com/AS5163
Revision 2.7
9 - 36
相关PDF资料 |
PDF描述 |
|---|---|
| D2HW-C262MR | SUBMINIATURE BASIC SWITCH |
| AS5140H-ASSU | IC ENCODER PROG 10-BIT 16-SSOP |
| D2HW-C262M | SUBMINIATURE BASIC SWITCH |
| A1354KKTTN-T | IC HALL EFFECT SENSOR 2WIRE 4SIP |
| D2HW-C261M | SUBMINIATURE BASIC SWITCH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5163-HTSV | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:12-Bit Automotive Angle Position Sensor |
| AS5163-TS_EK_AB | 功能描述:AS5163 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:模拟和数字 灵敏度:- 电压 - 电源:4.5 V ~ 5.5 V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5163 标准包装:1 |
| AS5163-TS_EK_DB | 功能描述:AS5163 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:9V 嵌入式:是，MCU，8 位 所含物品:板 使用的 IC/零件:AS5163 标准包装:1 |
| AS5165 AB | 制造商:ams 功能描述:ADAPTER BOARD FOR AS5165 制造商:ams 功能描述:Adapter Board |
| AS51650FLF | 制造商:TT Electronics / IRC 功能描述:AS51650FLF |
发布紧急采购，3分钟左右您将得到回复。