- 您现在的位置：买卖IC网 > PDF目录21914 > AS5163-HTSU (ams)IC ENCODER PROG 12-BIT 14TSSOP PDF资料下载
参数资料
| 型号： | AS5163-HTSU |
| 厂商： | ams |
| 文件页数： | 17/37页 |
| 文件大小： | 0K |
| 描述： | IC ENCODER PROG 12-BIT 14TSSOP |
| 应用说明： | AS5000 Series Magnet Selection Guide AS5000 Series Magnets for Extended Vertical Range |
| 特色产品： | AS5163 - Contactless Magnetic Angle Position Sensor |
| 标准包装： | 96 |
| 传感范围： | 30mT ~ 70mT |
| 类型： | 线性，旋转编码器 - 可编程 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 20mA |
| 输出类型： | 模拟，比率 |
| 特点： | 可编程 |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
AS5163
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8 Application Information
The benefits of AS5163 are as follows:
Unique fully differential patented solution
Best protection for automotive applications
Easy to program
Flexible interface selection PWM, analog output
Ideal for applications in harsh environments due to contactless position sensing
Robust system, tolerant to magnet misalignment, airgap variations, temperature variations and external magnetic fields
No calibration required because of inherent accuracy
High driving capability of analog output (including diagnostics)
8.1 Programming the AS5163
The AS5163 programming is a one-time-programming (OTP) method, based on polysilicon fuses. The advantage of this method is that no
additional programming voltage is needed. The internal LDO provides the current for programming.
The OTP consists of 128 bits, wherein several bits are available for user programming. In addition, factory settings are stored in the OTP
memory. Both regions are independently lockable by built-in lock bits.
A single OTP cell can be programmed only once. By default, each cell is “0”; a programmed cell will contain a “1”. While it is not possible to reset
a programmed bit from “1” to “0”, multiple OTP writes are possible, as long as only unprogrammed “0”-bits are programmed to “1”.
Independent of the OTP programming, it is possible to overwrite the OTP register temporarily with an OTP write command. This is possible only
if the user lock bit is not programmed.
Due to the programming over the output pin, the device will initially start in the communication mode. In this mode, the digital angle value can be
read with a specific protocol format. It is a bidirectional communication possible. Parameters can be written into the device. A programming of the
device is triggered by a specific command. With another command (pass2funcion), the device can be switched into operation mode (analog or
PWM output). In case of a programmed user lock bit, the AS5163 automatically starts up in the functional operation mode. No communication of
the specific protocol is possible after this.
8.1.1
Hardware Setup
The pin OUT and the supply connection are required for OTP memory access. Without the programmed Mem_Lock_USER OTP bit, the device
will start up in the communication mode and will remain into an IDLE operation mode. The pull up resistor R Communication is required during
startup. Figure 1 shows the configuration of an AS5163.
Figure 11. Programming Schematic of the AS5163
SENSOR PCB
1 μ F
VDD
VDD
AS5163
VDD5
VDD
Programmer
R Communication
2.2 μ F
(low ESR)
2.2 μ F
(low ESR)
0.3 ohm
VDD3
OUT
KDOWN
DIO
GNDA GNDD GNDP
GND
GND
www.austriamicrosystems.com/AS5163
Revision 2.7
16 - 36
相关PDF资料 |
PDF描述 |
|---|---|
| D2HW-C262MR | SUBMINIATURE BASIC SWITCH |
| AS5140H-ASSU | IC ENCODER PROG 10-BIT 16-SSOP |
| D2HW-C262M | SUBMINIATURE BASIC SWITCH |
| A1354KKTTN-T | IC HALL EFFECT SENSOR 2WIRE 4SIP |
| D2HW-C261M | SUBMINIATURE BASIC SWITCH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5163-HTSV | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:12-Bit Automotive Angle Position Sensor |
| AS5163-TS_EK_AB | 功能描述:AS5163 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:模拟和数字 灵敏度:- 电压 - 电源:4.5 V ~ 5.5 V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5163 标准包装:1 |
| AS5163-TS_EK_DB | 功能描述:AS5163 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:9V 嵌入式:是，MCU，8 位 所含物品:板 使用的 IC/零件:AS5163 标准包装:1 |
| AS5165 AB | 制造商:ams 功能描述:ADAPTER BOARD FOR AS5165 制造商:ams 功能描述:Adapter Board |
| AS51650FLF | 制造商:TT Electronics / IRC 功能描述:AS51650FLF |
发布紧急采购，3分钟左右您将得到回复。