- 您现在的位置：买卖IC网 > Datasheet目录961 > AS5245 DB (ams)BOARD DEMO AS5245 Datasheet资料下载
参数资料
| 型号： | AS5245 DB |
| 厂商： | ams |
| 文件页数： | 18/32页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO AS5245 |
| 标准包装： | 1 |
| 传感器类型： | 磁性，旋转位置 |
| 传感范围： | 360° |
| 接口： | USB |
| 电源电压： | 5V USB 或 9V |
| 嵌入式： | 是，MCU，8 位 |
| 已供物品： | 板，线缆 |
| 已用 IC / 零件： | AS5245 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AS5245
Data Sheet - A p p l i c a t i o n I n f o r m a t i o n
9 Application Information
The benefits of AS5245 are as follows:
Complete system-on-chip
Angle measurement with programmable range up to 360o
High reliability due to non-contact magnetic sensing
Ideal for applications in harsh environments
Robust system, tolerant to magnet misalignment, airgap variations, temperature variations and external magnetic fields
No calibration required
Building of redundancy systems with plausibility checks
9.1 Programming the AS5245
After power-on, programming the AS5245 is enabled with the rising edge of CSn with PDIO = high and CLK = low.
The AS5245 programming is a one-time programming (OTP) method, based on poly silicon fuses. The advantage of this method is that a
programming voltage of only 3.3V to 3.6V is required for programming.
The OTP consists of 52 bits, of which 21 bits are available for user programming. The remaining 31 bits contain factory settings and a unique
chip identifier (Chip-ID).
A single OTP cell can be programmed only once. Per default, the cell is “0”; a programmed cell will contain a “1”. While it is not possible to reset
a programmed bit from “1” to “0”, multiple OTP writes are possible, as long as only unprogrammed “0”-bits are programmed to “1”.
Independent of the OTP programming, it is possible to overwrite the OTP register temporarily with an OTP write command at any time. This
setting will be cleared and overwritten with the hard programmed OTP settings at each power-up sequence or by a LOAD operation. Use
application note AN514X_10 to get more information about the programming options.
The OTP memory can be accessed in the following ways:
Load Operation: The Load operation reads the OTP fuses and loads the contents into the OTP register. A Load operation is automatically
executed after each power-on-reset.
Write Operation: The Write operation allows a temporary modification of the OTP register. It does not program the OTP. This operation can
be invoked multiple times and will remain set while the chip is supplied with power and while the OTP register is not modified with another
Write or Load operation.
Read Operation: The Read operation reads the contents of the OTP register, for example to verify a Write command or to read the OTP
memory after a Load command.
Program Operation: The Program operation writes the contents of the OTP register permanently into the OTP ROM.
Analog Readback Operation: The Analog Readback operation allows a quantifiable verification of the programming. For each
programmed or unprogrammed bit, there is a representative analog value (in essence, a resistor value) that is read to verify whether a bit
has been successfully programmed or not.
9.1.1
Zero Position Programming
Zero position programming is an OTP option that simplifies assembly of a system, as the magnet does not need to be manually adjusted to the
mechanical zero position. Once the assembly is completed, the mechanical and electrical zero positions can be matched by software. Any
position within a full turn can be defined as the permanent new zero position.
For zero position programming, the magnet is turned to the mechanical zero position (e.g. the “off”-position of a rotary switch) and the actual
angular value is read.
This value is written into the OTP register bits Z35:Z46.
Note: The zero position value may also be modified before programming, e.g. to program an electrical zero position that is 180o (half turn)
from the mechanical zero position, just add 2048 to the value read at the mechanical zero position and program the new value into the
OTP register.
www.austriamicrosystems.com/AS5245
Revision 1.5
17 - 31
相关PDF资料 |
PDF描述 |
|---|---|
| AS5304-DK-1.0 | BOARD DEMO AS5304 |
| AS5311 DB | BOARD EVAL FOR AS5311 |
| ASEK712ELC-05B-T-DK | BOARD EVAL FOR ASEK712ELC-05B |
| ASPF240D3R | RELAY SSR 3A 240VAC SIP PHASE |
| ASX220A06 | RELAY TELECOM DPDT 10MA 6V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5245-HMFM | 功能描述:IC ENCODER ROTARY 32-QFN 制造商:ams 系列:汽车级，AEC-Q100 零件状态:有效 编码器类型:磁性 输出类型:正交（增量） 每转脉冲数:- 电压 - 电源:3 V ~ 3.6 V，4.5 V ~ 5.5 V 致动器类型:外磁铁，不含 棘爪:无 内置开关:无 安装类型:表面贴装 朝向:- 端子类型:SMD（SMT）接片 旋转寿命（最少次数）:- 标准包装:1 |
| AS5245-HMFP | 功能描述:IC ENCODER ROTARY 32QFN 制造商:ams 系列:汽车级，AEC-Q100 零件状态:有效 编码器类型:磁性 输出类型:正交（增量） 每转脉冲数:- 电压 - 电源:3 V ~ 3.6 V，4.5 V ~ 5.5 V 致动器类型:外磁铁，不含 棘爪:无 内置开关:无 安装类型:表面贴装 朝向:- 端子类型:SMD（SMT）接片 旋转寿命（最少次数）:- 标准包装:4,000 |
| AS5245HQFT | 制造商:ams 功能描述:QFN 32 |
| AS5245-HQFT | 功能描述:IC ENCODER PROG 32-QFN RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR |
| AS5245HQFT500 | 制造商:ams 功能描述:T&R / QFN 32 |
发布紧急采购，3分钟左右您将得到回复。