- 您现在的位置：买卖IC网 > PDF目录20507 > AT24C128-10TU-2.7 (Atmel)IC EEPROM 128KBIT 1MHZ 8TSSOP PDF资料下载
参数资料
| 型号： | AT24C128-10TU-2.7 |
| 厂商： | Atmel |
| 文件页数： | 10/23页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 128KBIT 1MHZ 8TSSOP |
| 标准包装： | 100 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 128K (16K x 8) |
| 速度： | 400kHz，1MHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 管件 |
Device
Addressing
Write
Operations
The 128K/256K EEPROM requires an 8-bit device address word following a start condition to
enable the chip for a read or write operation (see Figure 7 on page 11). The device address
word consists of a mandatory one, zero sequence for the first five most significant bits as
shown. This is common to all two-wire EEPROM devices.
The 128K/256K uses the two device address bits A1, A0 to allow as many as four devices on
the same bus. These bits must compare to their corresponding hardwired input pins. The A1
and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the
pins are allowed to float.
The eighth bit of the device address is the read/write operation select bit. A read operation is
initiated if this bit is high and a write operation is initiated if this bit is low.
Upon a compare of the device address, the EEPROM will output a zero. If a compare is not
made, the device will return to a standby state.
DATA SECURITY: The AT24C128/256 has a hardware data protection scheme that allows the
user to write protect the whole memory when the WP pin is at V CC .
BYTE WRITE: A write operation requires two 8-bit data word addresses following the device
address word and acknowledgment. Upon receipt of this address, the EEPROM will again
respond with a zero and then clock in the first 8-bit data word. Following receipt of the 8-bit
data word, the EEPROM will output a zero. The addressing device, such as a microcontroller,
then must terminate the write sequence with a stop condition. At this time the EEPROM enters
an internally-timed write cycle, t WR , to the nonvolatile memory. All inputs are disabled during
this write cycle and the EEPROM will not respond until the write is complete (see Figure 8 on
page 11).
PAGE WRITE: The 128K/256K EEPROM is capable of 64-byte page writes.
A page write is initiated the same way as a byte write, but the microcontroller does not send a
stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges
receipt of the first data word, the microcontroller can transmit up to 63 more data words. The
EEPROM will respond with a zero after each data word received. The microcontroller must ter-
minate the page write sequence with a stop condition (see Figure 9 on page 12).
The data word address lower 6 bits are internally incremented following the receipt of each
data word. The higher data word address bits are not incremented, retaining the memory page
row location. When the word address, internally generated, reaches the page boundary, the
following byte is placed at the beginning of the same page. If more than 64 data words are
transmitted to the EEPROM, the data word address will “roll over” and previous data will be
overwritten. The address “roll over” during write is from the last byte of the current page to the
first byte of the same page.
ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the
EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a
start condition followed by the device address word. The read/write bit is representative of the
operation desired. Only if the internal write cycle has completed will the EEPROM respond
with a zero, allowing the read or write sequence to continue.
10
AT24C128/256
0670T–SEEPR–3/07
相关PDF资料 |
PDF描述 |
|---|---|
| R1DA-240505/P-R | CONV DC/DC 1W 24V IN 5/5V OUT |
| R0.25S8-3.33.3/P-R | CONV DC/DC 0.25W 3.3VIN 3.3VOUT |
| R0.25S12-3.312-R | CONV DC/DC 0.25W 3.3V IN 12V OUT |
| AT24C11-10TU-2.7 | IC EEPROM 1KBIT 1MHZ 8TSSOP |
| 346-062-522-202 | CARDEDGE 62POS DUAL .125 GREEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT24C128-10UC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:I2C Serial EEPROM |
| AT24C128-10UC-1.8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:I2C Serial EEPROM |
| AT24C128-10UC-2.7 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:I2C Serial EEPROM |
| AT24C128-10UI | 制造商:未知厂家 制造商全称:未知厂家 功能描述:I2C Serial EEPROM |
| AT24C128-10UI-1.8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:I2C Serial EEPROM |
发布紧急采购，3分钟左右您将得到回复。