- 您现在的位置：买卖IC网 > PDF目录20507 > AT24C128-10TU-2.7 (Atmel)IC EEPROM 128KBIT 1MHZ 8TSSOP PDF资料下载
参数资料
| 型号： | AT24C128-10TU-2.7 |
| 厂商： | Atmel |
| 文件页数： | 11/23页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 128KBIT 1MHZ 8TSSOP |
| 标准包装： | 100 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 128K (16K x 8) |
| 速度： | 400kHz，1MHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 管件 |
AT24C128/256
Read
Operations
Read operations are initiated the same way as write operations with the exception that the
read/write select bit in the device address word is set to one. There are three read operations:
current address read, random address read and sequential read.
CURRENT ADDRESS READ: The internal data word address counter maintains the last
address accessed during the last read or write operation, incremented by one. This address
stays valid between operations as long as the chip power is maintained. The address “roll
over” during read is from the last byte of the last memory page, to the first byte of the first
page.
Once the device address with the read/write select bit set to one is clocked in and acknowl-
edged by the EEPROM, the current address data word is serially clocked out. The
microcontroller does not respond with an input zero but does generate a following stop condi-
tion (see Figure 10 on page 12).
RANDOM READ: A random read requires a “dummy” byte write sequence to load in the data
word address. Once the device address word and data word address are clocked in and
acknowledged by the EEPROM, the microcontroller must generate another start condition.
The microcontroller now initiates a current address read by sending a device address with the
read/write select bit high. The EEPROM acknowledges the device address and serially clocks
out the data word. The microcontroller does not respond with a zero but does generate a fol-
lowing stop condition (see Figure 11 on page 12).
SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a ran-
dom address read. After the microcontroller receives a data word, it responds with an
acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment
the data word address and serially clock out sequential data words. When the memory
address limit is reached, the data word address will “roll over” and the sequential read will con-
tinue. The sequential read operation is terminated when the microcontroller does not respond
with a zero but does generate a following stop condition (see Figure 12 on page 12).
Figure 7. Device Address
Figure 8. Byte Write
11
0670T–SEEPR–3/07
相关PDF资料 |
PDF描述 |
|---|---|
| R1DA-240505/P-R | CONV DC/DC 1W 24V IN 5/5V OUT |
| R0.25S8-3.33.3/P-R | CONV DC/DC 0.25W 3.3VIN 3.3VOUT |
| R0.25S12-3.312-R | CONV DC/DC 0.25W 3.3V IN 12V OUT |
| AT24C11-10TU-2.7 | IC EEPROM 1KBIT 1MHZ 8TSSOP |
| 346-062-522-202 | CARDEDGE 62POS DUAL .125 GREEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT24C128-10UC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:I2C Serial EEPROM |
| AT24C128-10UC-1.8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:I2C Serial EEPROM |
| AT24C128-10UC-2.7 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:I2C Serial EEPROM |
| AT24C128-10UI | 制造商:未知厂家 制造商全称:未知厂家 功能描述:I2C Serial EEPROM |
| AT24C128-10UI-1.8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:I2C Serial EEPROM |
发布紧急采购，3分钟左右您将得到回复。