参数资料
| 型号： | AT25010N-10SI-2.7 |
| 厂商： | Atmel |
| 文件页数： | 8/17页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 1KBIT 2.1MHZ 8SOIC |
| 标准包装： | 100 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 1K (128 x 8) |
| 速度： | 2.1MHz |
| 接口： | SPI 3 线串行 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
READ SEQUENCE (READ): Reading the AT25010/020/040 via the SO (Serial Output)
pin requires the following sequence. After the CS line is pulled low to select a device,
the READ op-code (including A8) is transmitted via the SI line followed by the byte
address to be read (A7-A0). Upon completion, any data on the SI line will be ignored.
The data (D7-D0) at the specified address is then shifted out onto the SO line. If only
one byte is to be read, the CS line should be driven high after the data comes out. The
READ sequence can be continued since the byte address is automatically incremented
and data will continue to be shifted out. When the highest address is reached, the
address counter will roll over to the lowest address allowing the entire memory to be
read in one continuous READ cycle.
WRITE SEQUENCE (WRITE): In order to program the AT25010/020/040, the Write
Protect pin (WP) must be held high and two separate instructions must be executed.
First, the device must be write enabled via the Write Enable (WREN) Instruction. Then
a Write (WRITE) Instruction may be executed. Also, the address of the memory loca-
tion(s) to be programmed must be outside the protected address field location selected
by the Block Write Protection Level. During an internal write cycle, all commands will be
ignored except the RDSR instruction.
A Write Instruction requires the following sequence. After the CS line is pulled low to
select the device, the WRITE op-code (including A8) is transmitted via the SI line fol-
lowed by the byte address (A7-A0) and the data (D7-D0) to be programmed.
Programming will start after the CS pin is brought high. (The LOW to High transition of
the CS pin must occur during the SCK low time immediately after clocking in the D0
(LSB) data bit.
The READY/BUSY status of the device can be determined by initiating a READ STA-
TUS REGISTER (RDSR) Instruction. If Bit 0 = 1, the WRITE cycle is still in progress. If
Bit 0 = 0, the WRITE cycle has ended. Only the READ STATUS REGISTER instruction
is enabled during the WRITE programming cycle.
The AT25010/020/040 is capable of an 8-byte PAGE WRITE operation. After each byte
of data is received, the three low order address bits are internally incremented by one;
the six high order bits of the address will remain constant. If more than 8 bytes of data
are transmitted, the address counter will roll over and the previously written data will be
overwritten. The AT25010/020/040 is automatically returned to the write disable state at
the completion of a WRITE cycle.
NOTE: If the WP pin is brought low or if the device is not Write enabled (WREN), the
device will ignore the Write instruction and will return to the standby state, when CS is
brought high. A new CS falling edge is required to re-initiate the serial communication.
8
AT25010/020/040
0606M–SEEPR–06/03
相关PDF资料 |
PDF描述 |
|---|---|
| SOMAM3703-10-2780HFCR | SYSTEM ON MODULE LV AM3703 |
| AT25010-10PI-2.7 | IC EEPROM 1KBIT 2.1MHZ 8DIP |
| AT24C64W-10SI-2.7 | IC EEPROM 64KBIT 400KHZ 8SOIC |
| AT24C64N-10SI-2.7 | IC EEPROM 64KBIT 400KHZ 8SOIC |
| AT24C64-10PI-2.7 | IC EEPROM 64KBIT 400KHZ 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT25010Y1-10YI-2.7 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:EEPROM |
| AT25010Y2-10YI-2.7 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:EEPROM |
| AT25016-0T3X | 制造商:Atmel Corporation 功能描述: |
| AT25020 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:SPI Serial EEPROMs |
| AT25020-10PA-2.7C | 制造商:未知厂家 制造商全称:未知厂家 功能描述:SERIAL EEPROM|256X8|CMOS|DIP|8PIN|PLASTIC |
发布紧急采购，3分钟左右您将得到回复。