收藏本站
参数资料
型号： AT32UC3L016-D3HR
厂商： Atmel
文件页数： 157/174页
文件大小： 0K
描述： MCU AVR32 16K FLASH 48TTLGA
产品培训模块： AVR® UC3 Introduction
标准包装： 1
系列： AVR®32 UC3 L
核心处理器： AVR
芯体尺寸： 32-位
速度： 50MHz
连通性： I²C，SPI，UART/USART
外围设备： 欠压检测/复位，DMA，POR，PWM，WDT
输入/输出数： 36
程序存储器容量： 16KB（16K x 8）
程序存储器类型： 闪存
RAM 容量： 8K x 8
电压 - 电源 (Vcc/Vdd)： 1.62 V ~ 3.6 V
数据转换器： A/D 9x12b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 48-UFLGA
包装： 标准包装
其它名称： AT32UC3L016-D3HRDKR
83
32099I–01/2012
AT32UC3L016/32/64
The page buffer is not automatically reset after a page write. The programmer should do this
manually by issuing the Clear Page Buffer flash command. This can be done after a page write,
or before the page buffer is loaded with data to be stored to the flash page.
8.5
Flash Commands
The FLASHCDW offers a command set to manage programming of the flash memory, locking
and unlocking of regions, and full flash erasing. See Section 8.8.2 for a complete list of
commands.
To run a command, the CMD field in the Flash Command Register (FCMD) has to be written
with the command number. As soon as the FCMD register is written, the FRDY bit in the Flash
Status Register (FSR) is automatically cleared. Once the current command is complete, the
FSR.FRDY bit is automatically set. If an interrupt has been enabled by writing a one to
FCR.FRDY, the interrupt request line of the Flash Controller is activated. All flash commands
except for Quick Page Read (QPR) and Quick User Page Read (QPRUP) will generate an inter-
rupt request upon completion if FCR.FRDY is one.
Any HSB bus transfers attempting to read flash memory when the FLASHCDW is busy execut-
ing a flash command will be stalled, and allowed to continue when the flash command is
complete.
After a command has been written to FCMD, the programming algorithm should wait until the
command has been executed before attempting to read instructions or data from the flash or
writing to the page buffer, as the flash will be busy. The waiting can be performed either by poll-
ing the Flash Status Register (FSR) or by waiting for the flash ready interrupt. The command
written to FCMD is initiated on the first clock cycle where the HSB bus interface in FLASHCDW
is IDLE. The user must make sure that the access pattern to the FLASHCDW HSB interface
contains an IDLE cycle so that the command is allowed to start. Make sure that no bus masters
such as DMA controllers are performing endless burst transfers from the flash. Also, make sure
that the CPU does not perform endless burst transfers from flash. This is done by letting the
CPU enter sleep mode after writing to FCMD, or by polling FSR for command completion. This
polling will result in an access pattern with IDLE HSB cycles.
All the commands are protected by the same keyword, which has to be written in the eight high-
est bits of the FCMD register. Writing FCMD with data that does not contain the correct key
and/or with an invalid command has no effect on the flash memory; however, the PROGE bit is
set in the Flash Status Register (FSR). This bit is automatically cleared by a read access to the
FSR register.
Writing a command to FCMD while another command is being executed has no effect on the
flash memory; however, the PROGE bit is set in the Flash Status Register (FSR). This bit is
automatically cleared by a read access to the FSR register.
If the current command writes or erases a page in a locked region, or a page protected by the
BOOTPROT fuses, the command has no effect on the flash memory; however, the LOCKE bit is
set in the FSR register. This bit is automatically cleared by a read access to the FSR register.
8.5.1
Write/Erase Page Operation
Flash technology requires that an erase must be done before programming. The entire flash can
be erased by an Erase All command. Alternatively, pages can be individually erased by the
Erase Page command.
The User page can be written and erased using the mechanisms described in this chapter.
相关PDF资料
PDF描述
AT42QT5480-CU QS444 IC SENSOR DUAL TOUCH 49-BGA
AT6010H-4QI IC FPGA 4NS 240PQFP
AT80C31X2-SLRUM MCU ROMLESS 31X2 5V 44-PLCC
AT80C51RD2-SLRUM IC MCU 80C51 HI PERFORM 44PLCC
AT85C51SND3B1-RTTUL IC DECODER/ENCODER DGTL 100-LQFP
相关代理商/技术参数
参数描述
AT32UC3L016-D3HT 功能描述:32位微控制器 - MCU UC3L-16KB Flash 85C RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT
AT32UC3L016-D3UR 功能描述:32位微控制器 - MCU UC3L-16KB Flash RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT
AT32UC3L016-ZAUR 功能描述:32位微控制器 - MCU UC3L-16KB Flash 85C RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT
AT32UC3L016-ZAUT 功能描述:32位微控制器 - MCU UC3L-16KB Flash RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT
AT32UC3L0256-AUR 功能描述:32位微控制器 - MCU UC3L-256KB FL 85C RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*