参数资料
| 型号： | AT32UC3L032-ZAUT |
| 厂商： | Atmel |
| 文件页数： | 94/174页 |
| 文件大小： | 0K |
| 描述： | IC MCU 32K FLASH 16K 48-VQFN |
| 产品培训模块： | MCU Product Line Introduction AVR® UC3 Introduction |
| 标准包装： | 2,080 |
| 系列： | AVR®32 UC3 L |
| 核心处理器： | AVR |
| 芯体尺寸： | 32-位 |
| 速度： | 50MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，DMA，POR，PWM，WDT |
| 输入/输出数： | 36 |
| 程序存储器容量： | 32KB（32K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 16K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.62 V ~ 3.6 V |
| 数据转换器： | A/D 9x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 包装： | 托盘 |
| 其它名称： | 32UC3L032-ZAUT 32UC3L032-ZAUT-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页当前第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页
45
32099I–01/2012
AT32UC3L016/32/64
7.5.10
Priority
If more than one PDCA channel is requesting transfer at a given time, the PDCA channels are
prioritized by their channel number. Channels with lower numbers have priority over channels
with higher numbers, giving channel zero the highest priority.
7.5.11
Error Handling
If the Memory Address Register (MAR) is set to point to an invalid location in memory, an error
will occur when the PDCA tries to perform a transfer. When an error occurs, the Transfer Error
bit in the Interrupt Status Register (ISR.TERR) will be set and the DMA channel that caused the
error will be stopped. In order to restart the channel, the user must program the Memory
Address Register to a valid address and then write a one to the Error Clear bit in the Control
Register (CR.ECLR). If the Transfer Error interrupt is enabled, an interrupt request will be gener-
ated when a transfer error occurs.
7.5.12
Peripheral Event Trigger
Peripheral events can be used to trigger PDCA channel transfers. Peripheral Event synchroniza-
tions are enabled by writing a one to the Event Trigger bit in the Mode Register (MR.ETRIG).
When set, all DMA requests will be blocked until a peripheral event is received. For each periph-
eral event received, only one data item is transferred. If no DMA requests are pending when a
peripheral event is received, the PDCA will start a transfer as soon as a peripheral event is
detected. If multiple events are received while the PDCA channel is busy transferring data, an
overflow condition will be signaled in the Peripheral Event System. Refer to the Peripheral Event
System chapter for more information.
7.6
Performance Monitors
Up to two performance monitors allow the user to measure the activity and stall cycles for PDCA
transfers. To monitor a PDCA channel, the corresponding channel number must be written to
one of the MON0/1CH fields in the Performance Control Register (PCONTROL) and a one must
be written to the corresponding CH0/1EN bit in the same register.
Due to performance monitor hardware resource sharing, the two monitor channels should NOT
be programmed to monitor the same PDCA channel. This may result in UNDEFINED perfor-
mance monitor behavior.
7.6.1
Measuring mechanisms
Three different parameters can be measured by each channel:
The number of data transfer cycles since last channel reset, both for read and write
The number of stall cycles since last channel reset, both for read and write
The maximum latency since last channel reset, both for read and write
These measurements can be extracted by software and used to generate indicators for bus
latency, bus load, and maximum bus latency.
Each of the counters has a fixed width, and may therefore overflow. When an overflow is
encountered in either the Performance Channel Data Read/Write Cycle registers (PRDATA0/1
and PWDATA0/1) or the Performance Channel Read/Write Stall Cycles registers (PRSTALL0/1
and PWSTALL0/1) of a channel, all registers in the channel are reset. This behavior is altered if
the Channel Overflow Freeze bit is one in the Performance Control register (PCON-
TROL.CH0/1OVF). If this bit is one, the channel registers are frozen when either DATA or
STALL reaches its maximum value. This simplifies one-shot readout of the counter values.
相关PDF资料 |
PDF描述 |
|---|---|
| 35650-51 | BNC RES CAP/CHAIN 50 OHMS |
| ATMEGA644A-PU | IC MCU AVR 64K FLASH 40PDIP |
| 46650-51 | BNC RES CAP 50 OHMS |
| ATTINY26L-8SU | ID MCU AVR 2K 5V 8MHZ 20-SOIC |
| ATTINY26L-8MU | ID MCU AVR 2K 5V 8MHZ 32-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT32UC3L064 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:32-bit Atmel AVR Microcontroller |
| AT32UC3L064_1 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:AVR32 32-bit Microcontroller |
| AT32UC3L064_10 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:32-bit AVR??Microcontroller |
| AT32UC3L064_11 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:32-bit Atmel AVR Microcontroller |
| AT32UC3L064-AUR | 功能描述:32位微控制器 - MCU UC3L-64KB Flash 85C RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。