- 您现在的位置：买卖IC网 > PDF目录67388 > AT42QT1110-AZ (ATMEL CORP) PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT PDF资料下载
参数资料
| 型号： | AT42QT1110-AZ |
| 厂商： | ATMEL CORP |
| 元件分类： | 速度传感器和接近开关 |
| 英文描述： | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| 封装： | 7 X 7 MM, 1 MM HEIGHT, 0.80 MM PITCH, ROHS COMPLIANT, PLASTIC, TQFP-32 |
| 文件页数： | 11/46页 |
| 文件大小： | 657K |
| 代理商： | AT42QT1110-AZ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
19
9570I–AT42–03/10
AT42QT1110-MZ/AT42QT1110-AZ
4.8.2
Synchronized Trigger
In 11-key mode, if a time trigger is not enabled, the QT1110 operates in “synchronized” mode. In
this mode, SNS10K is used as a SYNC pin to trigger key acquisition, rather than using the
device’s internal clock. In this case the maximum number of keys is reduced to 10.
The SYNC pin can use one of two methods to trigger key measurements, selectable via bit 4 of
the Device Mode setup byte (see Section 7.4 on page 29): Low Level and Rising Edge.
With the Low Level method the QT1110 operates in “free run” mode for as long as the SYNC pin
is read as a logical “0”. When the SYNC pin goes high, the current measurement cycle will be
finished and no more key measurements will be taken until the SYNC pin goes low again.
The low level trigger should be a minimum of 1 ms so that there is sufficient time for the device
to detect the low level.
With the Rising Edge method all enabled keys are measured once when a rising edge is
detected on the SYNC pin. This allows key measurements to be synchronized to an external
event or condition.
For example, the SYNC pin can be used by the host to synchronize several devices to each
other. This would ensure that only one of the devices outputs pulses at any given time and
signals from one QT1110 do not interfere with the measurements from another.
Another use for synchronizing to the rising edge is to steady the signals when the device is
running off a mains transformer with insufficient mains frequency filtering that is causing a 50Hz
or 60Hz ripple on Vdd. If the mains voltage is scaled down with a simple voltage divider and
connected to the SYNC pin, then the key measurement can be triggered by the rising edge
detected at a positive going zero-crossing. Note that in this case, each key signal will be taken at
the same point in the cycle, so Vdd will be the same at each measurement for a given key and
the signals will be steadier.
4.9
Guard Channel Option
The device has a guard channel option (available in all key modes), which allows one key to be
configured as a guard channel to help prevent false detection (see Figure 4-9 on page 20).
Guard channel keys should be more sensitive than the other keys (physically bigger or larger
Cs), subject to burst length limitations (see Section 4.11.2 on page 21).
With guard channel enabled, the designated key is connected to a sensor pad which detects the
presence of touch and overrides any output from the other keys using the chip’s AKS feature.
The guard channel option is enabled by the Guard Key setup byte (see Section 7.5 on page 30).
With the guard channel not enabled, all the keys work normally.
Note:
If a key is already “in detect” when the guard channel becomes active, that key will
remain in detect and the guard key will not activate until the active key goes out of
detect.
相关PDF资料 |
PDF描述 |
|---|---|
| AT42QT1110-MZ | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| AT42QT1111-AU | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| AT76C453AC-MY19T | IMAGE SENSOR-CMOS, 708(H) X 494(V) PIXEL, 30fps, SURFACE MOUNT |
| ATF-33143-TR2 | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
| ATF-33143-BLK | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT42QT1110-MU | 功能描述:电容触摸传感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 电源电压: 通道数量: 封装 / 箱体: 尺寸: 温度范围: |
| AT42QT1110-MU QS470 | 功能描述:IC TOUCH SENSOR 11KEY 32QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:QTouch™ 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AT42QT1110-MUR | 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC 制造商:microchip technology 系列:* 包装:剪切带（CT） 零件状态:在售 封装/外壳:32-VFQFN 裸露焊盘 供应商器件封装:32-QFN（5x5） 标准包装:1 |
| AT42QT1110-MZ | 功能描述:电容触摸传感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 电源电压: 通道数量: 封装 / 箱体: 尺寸: 温度范围: |
| AT42QT1111-AU | 功能描述:电容触摸传感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 电源电压: 通道数量: 封装 / 箱体: 尺寸: 温度范围: |
发布紧急采购，3分钟左右您将得到回复。