- 您现在的位置：买卖IC网 > PDF目录67388 > AT42QT1110-AZ (ATMEL CORP) PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT PDF资料下载
参数资料
| 型号： | AT42QT1110-AZ |
| 厂商： | ATMEL CORP |
| 元件分类： | 速度传感器和接近开关 |
| 英文描述： | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| 封装： | 7 X 7 MM, 1 MM HEIGHT, 0.80 MM PITCH, ROHS COMPLIANT, PLASTIC, TQFP-32 |
| 文件页数： | 29/46页 |
| 文件大小： | 657K |
| 代理商： | AT42QT1110-AZ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
37
4519 Group
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
(1) Timer control registers
Timer control register PA
Register PA controls the count operation of prescaler. Set the
contents of this register through register A with the TPAA instruc-
tion.
Timer control register W1
Register W1 controls the selection of timer 1 count auto-stop cir-
cuit, and the count operation and count source of timer 1. Set the
contents of this register through register A with the TW1A instruc-
tion. The TAW1 instruction can be used to transfer the contents
of register W1 to register A.
Timer control register W2
Register W2 controls the selection of CNTR0 output, and the
count operation and count source of timer 2. Set the contents of
this register through register A with the TW2A instruction. The
TAW2 instruction can be used to transfer the contents of register
W2 to register A.
Timer control register W3
Register W3 controls the selection of the count operation and
count source of timer 3 count auto-stop circuit. Set the contents
of this register through register A with the TW3A instruction. The
TAW3 instruction can be used to transfer the contents of register
W3 to register A.
Timer control register W4
Register W4 controls the D7/CNTR1 output, the expansion of “H”
interval of PWM output, and the count operation and count
source of timer 4. Set the contents of this register through regis-
ter A with the TW4A instruction. The TAW4 instruction can be
used to transfer the contents of register W4 to register A.
Timer control register W5
Register W5 controls the period measurement circuit and target
signal for period measurement. Set the contents of this register
through register A with the TW5A instruction. The TAW5 instruc-
tion can be used to transfer the contents of register W5 to
register A.
Timer control register W6
Register W6 controls the count edges of CNTR0 pin and CNTR1
pin, selection of CNTR1 output auto-control circuit and the D6/
CNTR0 pin function. Set the contents of this register through reg-
ister A with the TW6A instruction. The TAW6 instruction can be
used to transfer the contents of register W6 to register A..
(2) Prescaler
Prescaler is an 8-bit binary down counter with the prescaler reload
register PRS. Data can be set simultaneously in prescaler and the
reload register RPS with the TPSAB instruction. Data can be read
from reload register RPS with the TABPS instruction.
Stop counting and then execute the TPSAB or TABPS instruction
to read or set prescaler data.
Prescaler starts counting after the following process;
set data in prescaler, and
set the bit 0 of register PA to “1.”
When a value set in reload register RPS is n, prescaler divides the
count source signal by n + 1 (n = 0 to 255).
Count source for prescaler is the instruction clock (INSTCK).
Once count is started, when prescaler underflows (the next count
pulse is input after the contents of prescaler becomes “0”), new
data is loaded from reload register RPS, and count continues
(auto-reload function).
The output signal (ORCLK) of prescaler can be used for timer 1, 2,
3, and 4 count sources.
(3) Timer 1 (interrupt function)
Timer 1 is an 8-bit binary down counter with the timer 1 reload reg-
ister (R1). Data can be set simultaneously in timer 1 and the reload
register (R1) with the T1AB instruction. Data can be written to re-
load register (R1) with the TR1AB instruction. Data can be read
from timer 1 with the TAB1 instruction.
Stop counting and then execute the T1AB or TAB1 instruction to
read or set timer 1 data.
When executing the TR1AB instruction to set data to reload regis-
ter R1 while timer 1 is operating, avoid a timing when timer 1
underflows.
Timer 1 starts counting after the following process;
set data in timer 1
set count source by bits 0 and 1 of register W1, and
set the bit 2 of register W1 to “1.”
When a value set in reload register R1 is n, timer 1 divides the
count source signal by n + 1 (n = 0 to 255).
Once count is started, when timer 1 underflows (the next count
pulse is input after the contents of timer 1 becomes “0”), the timer
1 interrupt request flag (T1F) is set to “1,” new data is loaded from
reload register R1, and count continues (auto-reload function).
INT0 pin input can be used as the start trigger for timer 1 count op-
eration by setting the bit 0 of register I1 to “1.”
Also, in this time, the auto-stop function by timer 1 underflow can
be performed by setting the bit 3 of register W1 to “1.”
Timer 1 underflow signal divided by 2 can be output from CNTR0
pin by clearing bit 3 of register W2 to “0” and setting bit 0 of regis-
ter W6 to “1”.
The period measurement circuit starts operating by setting bit 2 of
register W5 to “1” and timer 1 is used to count the one-period of the
target signal for the period measurement. In this time, the timer 1
interrupt request flag (T1F) is not set by the timer 1 underflow sig-
nal, it is the flag for detecting the completion of period
measurement.
相关PDF资料 |
PDF描述 |
|---|---|
| AT42QT1110-MZ | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| AT42QT1111-AU | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| AT76C453AC-MY19T | IMAGE SENSOR-CMOS, 708(H) X 494(V) PIXEL, 30fps, SURFACE MOUNT |
| ATF-33143-TR2 | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
| ATF-33143-BLK | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT42QT1110-MU | 功能描述:电容触摸传感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 电源电压: 通道数量: 封装 / 箱体: 尺寸: 温度范围: |
| AT42QT1110-MU QS470 | 功能描述:IC TOUCH SENSOR 11KEY 32QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:QTouch™ 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AT42QT1110-MUR | 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC 制造商:microchip technology 系列:* 包装:剪切带（CT） 零件状态:在售 封装/外壳:32-VFQFN 裸露焊盘 供应商器件封装:32-QFN（5x5） 标准包装:1 |
| AT42QT1110-MZ | 功能描述:电容触摸传感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 电源电压: 通道数量: 封装 / 箱体: 尺寸: 温度范围: |
| AT42QT1111-AU | 功能描述:电容触摸传感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 电源电压: 通道数量: 封装 / 箱体: 尺寸: 温度范围: |
发布紧急采购，3分钟左右您将得到回复。