参数资料
型号: AT86RF401U
厂商: ATMEL CORP
元件分类: 通信及网络
英文描述: Smart RF Wireless Data Microtransmitter
中文描述: SPECIALTY TELECOM CIRCUIT, PDSO20
封装: 4.40 X 6.50 MM, 0.65 MM PITCH, TSSOP-20
文件页数: 42/52页
文件大小: 479K
代理商: AT86RF401U
42
AT86RF401
1424F
RKE
12/03
code execution at the reset location. This bit is reset at POR and when exiting the button
reset state. All other registers remain unchanged.
Button Detect Register
B_DET
Bits[7:6]
Reserved. These bits read
0
.
Bits[5:0]
When an I/O pin is configured as a button using the IO_ENAB and IO_DATOUT regis-
ters and a logic low is detected on that pin, the button detect logic is activated. If the part
is in sleep mode, the part responds as described in the AVR Configuration Register
description. If a good battery is present, the appropriate bit is set in this register. A bit in
this register is cleared by writing a
0
to it.
Battery Low Configuration Register
BL_CONFIG
Bit[7]: Battery Low
When Bit[6] in this register is set (Battery Low Valid), the BL (Battery Low) bit indicates
that the battery voltage is lower than the voltage level that is determined by Bit[5:0] of
this register. It is important that the programmer also check Bit[6] (Battery Low Valid) to
be certain that this condition is valid.
Bit[6]: Battery Low Valid
When the Battery Low Configuration Register is written, this bit is set to
0
. When the
battery voltage has been sampled and compared to the voltage determined by the BLx
bits, this bit is set to
1
indicating that the data in Bit[7] (Battery Low) is valid. This can
take up to 3100 XTAL cycles to complete.
Note:
The programmer should ensure that this bit is cleared prior to making a determination of
the Battery Low status. This can be done by reloading Bit[5] or directly clearing Bit[6].
Generally, the programmer loads Bit[5], loops until Bit[6] is set, and then checks Bit[3] to
determine the status of the battery.
Bit[5:0]: Battery Low Detection Level
This value is sent to the battery monitor. The threshold is calculated using the formulas
shown in Table 21 on page 43.
Note:
This threshold can be set below the brown-out voltage level.
Bit
7
6
5
4
3
2
1
0
$34
BD5
BD4
BD3
BD2
BD1
BD0
Read/Write
R
R
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
Bit
7
6
5
4
3
2
1
0
$35
BL
BLV
BL5
BL4
BL3
BL2
BL1
BL0
Read/Write
R
R
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
相关PDF资料
PDF描述
AT86RF401X Smart RF Wireless Data Microtransmitter
AT86RF535A WiMax Transceiver 802.16-2004
AT86RF535B 3.5GHz WiMAX Transceiver
AT86ZL3201 AT86ZL3201 Z-Link⑩ Controller Customized for IEEE 802.15.4 and ZigBee⑩ Wireless Systems
AT87251G2D-SLSUL B/16-BIT MICROCONTROLLER WITH SERIAL COMMUNICATION INTERFACES
相关代理商/技术参数
参数描述
AT86RF401U-6GS 功能描述:IC MICRO TRANSM RF W/AVR 20TSSOP RoHS:否 类别:RF/IF 和 RFID >> RF 发射器 系列:- 标准包装:4,000 系列:- 频率:310MHz ~ 440MHz 应用:- 调制或协议:UHF,ASK 数据传输率 - 最大:20 kBaud 功率 - 输出:1dBm ~ 5dBm 电流 - 传输:10mA 数据接口:PCB,表面贴装 天线连接器:PCB,表面贴装 存储容量:- 特点:- 电源电压:2.2 V ~ 4 V 工作温度:-40°C ~ 85°C 封装/外壳:16-LSSOP(0.154",3.90mm 宽) 包装:带卷 (TR)
AT86RF401UEK1 制造商:Atmel Corporation 功能描述:Smart RF Wireless Data Microtransmitter
AT86RF401U-EK1 功能描述:射频发射器 Smart RF Micro Trans RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel
AT86RF401U-XI 功能描述:IC MICRO TX RF W/AVR 20-TSSOP RoHS:否 类别:RF/IF 和 RFID >> RF 发射器 系列:- 标准包装:4,000 系列:- 频率:310MHz ~ 440MHz 应用:- 调制或协议:UHF,ASK 数据传输率 - 最大:20 kBaud 功率 - 输出:1dBm ~ 5dBm 电流 - 传输:10mA 数据接口:PCB,表面贴装 天线连接器:PCB,表面贴装 存储容量:- 特点:- 电源电压:2.2 V ~ 4 V 工作温度:-40°C ~ 85°C 封装/外壳:16-LSSOP(0.154",3.90mm 宽) 包装:带卷 (TR)
AT86RF401X 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Smart RF Wireless Data Microtransmitter