参数资料
型号: AT89C51CC01CA-SLSUM
厂商: Atmel
文件页数: 46/123页
文件大小: 0K
描述: IC 8051 MCU 32K FLASH 44-PLCC
产品培训模块: MCU Product Line Introduction
标准包装: 972
系列: AT89C CAN
核心处理器: 8051
芯体尺寸: 8-位
速度: 40MHz
连通性: CAN,UART/USART
外围设备: POR,PWM,WDT
输入/输出数: 34
程序存储器容量: 32KB(32K x 8)
程序存储器类型: 闪存
EEPROM 大小: 2K x 8
RAM 容量: 1.25K x 8
电压 - 电源 (Vcc/Vdd): 3 V ~ 5.5 V
数据转换器: A/D 8x10b
振荡器型: 外部
工作温度: -40°C ~ 85°C
封装/外壳: 44-LCC(J 形引线)
包装: 管件
产品目录页面: 616 (CN2011-ZH PDF)
配用: AT89OCD-01-ND - USB EMULATOR FOR AT8XC51 MCU
14
A/T89C51CC01
4129N–CAN–03/08
Clock
The T89C51CC01 core needs only 6 clock periods per machine cycle. This feature,
called ”X2”, provides the following advantages:
Divides frequency crystals by 2 (cheaper crystals) while keeping the same CPU
power.
Saves power consumption while keeping the same CPU power (oscillator power
saving).
Saves power consumption by dividing dynamic operating frequency by 2 in
operating and idle modes.
Increases CPU power by 2 while keeping the same crystal frequency.
In order to keep the original C51 compatibility, a divider-by-2 is inserted between the
XTAL1 signal and the main clock input of the core (phase generator). This divider may
be disabled by the software.
An extra feature is available to start after Reset in the X2 mode. This feature can be
enabled by a bit X2B in the Hardware Security Byte. This bit is described in the section
"In-System-Programming".
Description
The X2 bit in the CKCON register (see Table 12) allows switching from 12 clock cycles
per instruction to 6 clock cycles and vice versa. At reset, the standard speed is activated
(STD mode).
Setting this bit activates the X2 feature (X2 mode) for the CPU Clock only (see Figure
The Timers 0, 1 and 2, Uart, PCA, Watchdog or CAN switch in X2 mode only if the cor-
responding bit is cleared in the CKCON register.
The clock for the whole circuit and peripheral is first divided by two before being used by
the CPU core and peripherals. This allows any cyclic ratio to be accepted on the XTAL1
input. In X2 mode, as this divider is bypassed, the signals on XTAL1 must have a cyclic
ratio between 40 to 60%. Figure 5. shows the clock generation block diagram. The X2
bit is validated on the XTAL1÷2 rising edge to avoid glitches when switching from the X2
to the STD mode. Figure 6 shows the mode switching waveforms.
相关PDF资料
PDF描述
VI-J0J-IY-F2 CONVERTER MOD DC/DC 36V 50W
VJ2225A222JBLAT4X CAP CER 2200PF 630V 5% NP0 2225
VI-23Y-IY-F2 CONVERTER MOD DC/DC 3.3V 33W
VI-23Y-IY-F1 CONVERTER MOD DC/DC 3.3V 33W
VI-J0J-IY-F1 CONVERTER MOD DC/DC 36V 50W
相关代理商/技术参数
参数描述
AT89C51CC01CU-SLSUM 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89C51CC01SA-RLTUM 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Enhanced 8-bit Microcontroller with CAN Controller and Flash Memory
AT89C51CC01SA-SLSUM 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Enhanced 8-bit Microcontroller with CAN Controller and Flash Memory
AT89C51CC01UA-7CTUM 制造商:Rochester Electronics LLC 功能描述: 制造商:Atmel Corporation 功能描述:
AT89C51CC01UA-RLRUM 功能描述:8位微控制器 -MCU CAN Boot UART Ind RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT