参数资料
型号: AT89C51RC2-3CSIM
厂商: Atmel
文件页数: 100/127页
文件大小: 0K
描述: IC 8051 MCU FLASH 32K 40DIP
标准包装: 9
系列: 89C
核心处理器: 8051
芯体尺寸: 8-位
速度: 60MHz
连通性: SPI,UART/USART
外围设备: POR,PWM,WDT
输入/输出数: 32
程序存储器容量: 32KB(32K x 8)
程序存储器类型: 闪存
RAM 容量: 1.25K x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 5.5 V
振荡器型: 外部
工作温度: -40°C ~ 85°C
封装/外壳: 40-DIP(0.600",15.24mm)
包装: 管件
配用: AT89STK-11-ND - KIT STARTER FOR AT89C51RX2
74
AT89C51RB2/RC2
4180E–8051–10/06
Figure 31. SPI Interrupt Requests Generation
Registers
There are three registers in the Module that provide control, status and data storage functions. These registers
are describes in the following paragraphs.
Serial Peripheral Control
Register (SPCON)
The Serial Peripheral Control Register does the following:
Selects one of the Master clock rates
Configure the SPI Module as Master or Slave
Selects serial clock polarity and phase
Enables the SPI Module
Frees the SS pin for a general-purpose
Table 56 describes this register and explains the use of each bit
Table 56. SPCON Register
SPCON - Serial Peripheral Control Register (0C3H)
SSDIS
MODF
CPU Interrupt Request
SPI Receiver/error
CPU Interrupt Request
SPI Transmitter
SPI
CPU Interrupt Request
SPIF
76
54
32
1
0
SPR2
SPEN
SSDIS
MSTR
CPOL
CPHA
SPR1
SPR0
Bit Number
Bit Mnemonic
Description
7
SPR2
Serial Peripheral Rate 2
Bit with SPR1 and SPR0 define the clock rate.
6
SPEN
Serial Peripheral Enable
Cleared to disable the SPI interface.
Set to enable the SPI interface.
5SSDIS
SS Disable
Cleared to enable SS in both Master and Slave modes.
Set to disable SS in both Master and Slave modes. In Slave mode,
this bit has no effect if CPHA =’0’. When SSDIS is set, no MODF
interrupt request is generated
.
4MSTR
Serial Peripheral Master
Cleared to configure the SPI as a Slave.
Set to configure the SPI as a Master.
3CPOL
Clock Polarity
Cleared to have the SCK set to ’0’ in idle state.
Set to have the SCK set to ’1’ in idle low.
2CPHA
Clock Phase
Cleared to have the data sampled when the SCK leaves the idle
state (see CPOL).
Set to have the data sampled when the SCK returns to idle state (see
CPOL).
相关PDF资料
PDF描述
AT89C51RB2-SLSIM IC 8051 MCU FLASH 16K 44PLCC
AT89C51RB2-SLSIL IC 8051 MCU FLASH 16K 44PLCC
PIC16C72A-04/SP IC MCU OTP 2KX14 A/D PWM 28DIP
AT89C51RB2-RLTIM IC 8051 MCU FLASH 16K 44VQFP
AT89C51RB2-3CSIM IC 8051 MCU FLASH 16K 40DIP
相关代理商/技术参数
参数描述
AT89C51RC2-3CSUM 功能描述:8位微控制器 -MCU 32kB Flash 1280B RAM 2.7V-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89C51RC-24AC 功能描述:8位微控制器 -MCU 32K FLASH 4.0 TO 5.5V - 24MHZ RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89C51RC-24AI 功能描述:8位微控制器 -MCU 32K FLASH 4.0 TO 5.5V - 24MHZ RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89C51RC-24AU 功能描述:8位微控制器 -MCU 32K FLASH 4.0 TO 5.5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89C51RC-24JC 功能描述:8位微控制器 -MCU 32K FLASH 4.0 TO 5.5V - 24MHZ RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT