参数资料
型号: AT89S8253-24AC
厂商: Atmel
文件页数: 33/60页
文件大小: 0K
描述: IC 8051 MCU FLASH 12K 44TQFP
标准包装: 160
系列: 89S
核心处理器: 8051
芯体尺寸: 8-位
速度: 24MHz
连通性: SPI,UART/USART
外围设备: POR,WDT
输入/输出数: 32
程序存储器容量: 12KB(12K x 8)
程序存储器类型: 闪存
EEPROM 大小: 2K x 8
RAM 容量: 256 x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 5.5 V
振荡器型: 内部
工作温度: 0°C ~ 70°C
封装/外壳: 44-TQFP
包装: 托盘
39
3286P–MICRO–3/10
AT89S8253
21. Programming Interface
Every code byte in the Flash and EEPROM arrays can be written, and the entire array can be
erased, by using the appropriate combination of control signals. The write operation cycle is self-
timed and once initiated, will automatically time itself to completion.
Most worldwide major programming vendors offer support for the Atmel AT89 microcontroller
series. Please contact your local programming vendor for the appropriate software revision.
22. Serial Downloading
Both the code and data memory arrays can be programmed using the serial SPI bus while RST
is pulled to V
CC. The serial interface consists of pins SCK, MOSI (input) and MISO (output). After
RST is set high, the Programming Enable instruction must be executed first before other opera-
tions can be executed.
The Chip Erase operation turns the content of every memory location in both the Code and Data
arrays into FFH.
The code and data memory arrays have separate address spaces:
0000H to 2FFFH for code memory and 000H to 7FFH for data memory.
Either an external system clock is supplied at pin XTAL1 or a crystal needs to be connected
across pins XTAL1 and XTAL2. The maximum serial clock (SCK) frequency should be less than
1/16 of the crystal frequency. With a 24 MHz oscillator clock, the maximum SCK frequency is
1.5 MHz.
23. Serial Programming Algorithm
To program and verify the AT89S8253 in the serial programming mode, the following sequence
is recommended:
1.
Power-up sequence:
a.
Apply power between VCC and GND pins.
b.
Set RST pin to “H”.
If a crystal is not connected across pins XTAL1 and XTAL2, apply a 3 MHz to 12 MHz clock to
XTAL1 pin and wait for at least 10 ms with RST pin high and P1.7 (SCK) low.
2.
Enable serial programming by sending the Programming Enable serial instruction to pin
MOSI/P1.5. The frequency of the shift clock supplied at pin SCK/P1.7 needs to be less
than the CPU clock at XTAL1 divided by 16.
3.
The code or data array is programmed one byte or one page at a time by supplying the
address and data together with the appropriate Write instruction. The write cycle is self-
timed and typically takes less than 4.0 ms at 5V.
4.
Any memory location can be verified by using the Read instruction which returns the
content at the selected address at serial output MISO/P1.6.
5.
At the end of a programming session, RST can be set low to commence normal
operation.
Power-off sequence (if needed):
1.
Set XTAL1 to “L” (if a crystal is not used).
2.
Set RST to “L”.
3.
Turn V
CC power off.
相关PDF资料
PDF描述
AT89LP4052-16XI IC 8051 MCU FLASH 4K 20TSSOP
DSPIC33FJ64GS406-I/MR IC MCU/DSP 64KB FLASH 64QFN
PIC24HJ64GP502-I/MM IC PIC MCU FLASH 64K 28-QFN
AT89LP4052-16SI IC 8051 MCU FLASH 4K 20SOIC
AT89LP4052-16PU IC 8051 MCU FLASH 4K 20DIP
相关代理商/技术参数
参数描述
AT89S8253-24AI 功能描述:8位微控制器 -MCU UNSAWN WAFER 20 MIL BACKGRIND - 24MHZ RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89S8253-24AU 功能描述:8位微控制器 -MCU 12kB Flash 256B RAM 2.7V-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89S8253-24AU SL383 制造商:Atmel Corporation 功能描述:MCU 8-bit AT89 80C51 CISC 12KB Flash 3.3V/5V 44-Pin TQFP T/R
AT89S8253-24JC 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89S825324JI 制造商:Atmel Corporation 功能描述: