参数资料
| 型号： | AT91FR40162SB-CU |
| 厂商： | Atmel |
| 文件页数： | 5/22页 |
| 文件大小： | 0K |
| 描述： | IC ARM MCU FLASH 1K 121BGA |
| 标准包装： | 2,250 |
| 系列： | AT91 |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 75MHz |
| 连通性： | EBI/EMI，UART/USART |
| 外围设备： | WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 2MB（1M x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 256K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.65 V ~ 1.95 V |
| 振荡器型： | 外部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 121-BGA |
| 包装： | 托盘 |
13
6410BS–ATARM–12-Jan-10
AT91FR40162SB
be redefined dynamically by the software, the AT91FR40162SB uses a remap command that
enables switching between the boot memory and the internal primary SRAM bank addresses.
The remap command is accessible through the EBI User Interface by writing one in RCB of
EBI_RCR (Remap Control Register). Performing a remap command is mandatory if access to
the other external devices (connected to chip selects 1 to 7) is required. The remap operation
can only be changed back by an internal reset or an NRST assertion.
7.6.4
Abort Control
The abort signal providing a Data Abort or a Prefetch Abort exception to the ARM7TDMI is
asserted when accessing an undefined address in the EBI address space.
No abort is generated when reading the internal memory or by accessing the internal peripher-
als, whether the address is defined or not.
7.6.5
External Bus Interface
The External Bus Interface handles the accesses between addresses 0x0040 0000 and 0xFFC0
0000. It generates the signals that control access to the external devices, and can be configured
from eight 1-Mbyte banks up to four 16-Mbyte banks. It supports byte, half-word and word
aligned accesses.
For each of these banks, the user can program:
Number of wait states
Number of data float times (wait time after the access is finished to prevent any bus
contention in case the device is too long in releasing the bus)
Data bus width (8-bit or 16-bit)
With a 16-bit wide data bus, the user can program the EBI to control one 16-bit device (Byte
Access Select Mode) or two 8-bit devices in parallel that emulate a 16-bit memory (Byte
Write Access Mode).
The External Bus Interface features also the Early Read Protocol, configurable for all the
devices, that significantly reduces access time requirements on an external device in the case of
single-clock cycle access.
In the AT91FR40162SB, the External Bus Interface connects internally to the Flash memory.
7.6.6
Flash Memory
The 2-Mbyte Flash memory is organized as 1, 048, 576 words of 16 bits each. The Flash mem-
ory is addressed as 16-bit words via the EBI. It uses address lines A1 - A20 of the processor.
The address, data and control signals, except the Flash memory enable, are internally intercon-
nected. The user should connect the Flash memory enable (NCSF) to one of the active-low chip
selects on the EBI; NCS0 must be used if the Flash memory is to be the boot memory. In addi-
tion, if the Flash memory is to be used as boot memory, the BMS input must be pulled down
externally in order for the processor to perform correct 16-bit fetches after reset.
During boot, the EBI must be configured with correct number of standard wait states. As an
example, five standard wait states are required when the microcontroller is running at 66 MHz.
The user must ensure that all VDDIO, VDDCORE and all GND pins are connected to their
respective supplies by the shortest route. The Flash memory powers-on in read mode. Com-
mand sequences are used to place the device in other operating modes, such as program and
erase.
相关PDF资料 |
PDF描述 |
|---|---|
| AT91SAM7X256-AU-999 | IC ARM7 MCU 256K FLASH 100-LQFP |
| PIC16LF873-04/SP | IC MCU FLASH 4KX14 EE A/D 28DIP |
| PIC16LF873-04/SO | IC MCU FLASH 4KX14 EE A/D 28SOIC |
| PIC18LF2515-I/SO | IC MCU FLASH 24KX16 28SOIC |
| DSPIC30F4012-20I/SO | IC DSPIC MCU/DSP 48K 28SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT91FR40162SB-CU-999 | 功能描述:ARM微控制器 - MCU BGA MRL B IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91FR40162SBPRE | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Flash memory in a single compact 121-ball BGA package |
| AT91FR40162S-CJ | 功能描述:ARM微控制器 - MCU 256K SRAM 2M FLASH IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91FR40162S-CJ SL383 | 制造商:Atmel Corporation 功能描述:MCU 32-bit 91F ARM7TDMI RISC 2048KB Flash 1.8V 121-Pin BGA T/R |
| AT91FR4042 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:AT91 ARM Thumb Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。