参数资料
型号: AT91M42800A-33CJ
厂商: Atmel
文件页数: 6/27页
文件大小: 0K
描述: IC ARM7 MCU 144 BGA
产品培训模块: MCU Product Line Introduction
标准包装: 160
系列: AT91
核心处理器: ARM7
芯体尺寸: 16/32-位
速度: 33MHz
连通性: EBI/EMI,SPI,UART/USART
外围设备: WDT
输入/输出数: 54
程序存储器类型: ROMless
RAM 容量: 8K x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 3.6 V
振荡器型: 外部
工作温度: -40°C ~ 85°C
封装/外壳: 144-LFBGA
包装: 托盘
配用: AT91EB42-ND - KIT EVAL FOR ARM AT91M42800A
14
1779ES–ATARM–14-Apr-06
AT91M42800A
7.6.3
IEEE 1149.1 JTAG Boundary Scan
IEEE 1149.1 JTAG Boundary Scan is enabled when MODE0 is low and MODE1 is high. The
functions SAMPLE, EXTEST and BYPASS are implemented. In ICE Debug mode, the ARM
core responds with a non-JTAG chip ID that identifies the core to the ICE system. This is not
IEEE 1149.1 JTAG compliant. It is not possible to switch directly between JTAG and ICE opera-
tions. A chip reset must be performed (NRST and NTRST) after MODE0 and MODE1 are
changed.
7.7
Memory Controller
The ARM7TDMI processor address space is 4G bytes. The memory controller decodes the
internal 32-bit address bus and defines three address spaces:
Internal Memories in the four lowest megabytes
Middle Space reserved for the external devices (memory or peripherals) controlled by the
EBI
Internal Peripherals in the four highest megabytes
In any of these address spaces, the ARM7TDMI operates in little-endian mode only.
7.7.1
Protection Mode
The embedded peripherals can be protected against unwanted access. The PME (Protect Mode
Enable) pin must be tied high and validated in its peripheral operation (PIO Disable) to enable
the protection mode. When enabled, any peripheral access must be done while the ARM7TDMI
is running in Privileged mode (i.e., the accesses in user mode result in an abort). Only the valid
peripheral address space is protected and requests to the undefined addresses will lead to a
normal operation without abort.
7.7.2
Internal Memories
The AT91M42800A microcontroller integrates an 8-Kbyte primary internal SRAM. All internal
memories are 32 bits wide and single-clock cycle accessible. Byte (8-bit), half-word (16-bit) or
word (32-bit) accesses are supported and are executed within one cycle. Fetching Thumb or
ARM instructions is supported and internal memory can store twice as many Thumb instructions
as ARM ones.
The SRAM bank is mapped at address 0x0 (after the remap command), and ARM7TDMI excep-
tion vectors between 0x0 and 0x20 that can be modified by the software. The rest of the bank
can be used for stack allocation (to speed up context saving and restoring), or as data and pro-
gram storage for critical algorithms.
7.7.3
Boot Mode Select
The ARM reset vector is at address 0x0. After the NRST line is released, the ARM7TDMI exe-
cutes the instruction stored at this address. This means that this address must be mapped in
nonvolatile memory after the reset.
The input level on the BMS pin during the last 10 SLCK clock cycles before the rising edge of the
NRST selects the type of boot memory. The Boot mode depends on BMS (see Table 7-1).
相关PDF资料
PDF描述
AT91M55800A-33AU IC ARM MCU 33MHZ 176-LQFP
AT91R40008-66AU IC ARM7 MCU 100 LQFP
AT91RM9200-QI-002 SL383 IC ARM MCU 16BIT 128K 208PQFP
AT91SAM7A3-AU IC ARM7 MCU FLASH 256K 100LQFP
AT91SAM7S321-AU IC ARM7 MCU FLASH 32K 64LQFP
相关代理商/技术参数
参数描述
AT91M42800A-33CJ-999 功能描述:ARM微控制器 - MCU BGA Ind. Temp RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
AT91M43300 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:ARM Thumb Microcontrollers
AT91M43300-12CC-1.8 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:ARM Thumb Microcontrollers
AT91M43300-12CI-1.8 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:ARM Thumb Microcontrollers
AT91M43300-25CC 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:ARM Thumb Microcontrollers