- 您现在的位置：买卖IC网 > PDF目录11825 > ATMEGA325V-8AUR (Atmel)MCU AVR 32K FLASH 8MHZ 64TQFP PDF资料下载
参数资料
| 型号： | ATMEGA325V-8AUR |
| 厂商： | Atmel |
| 文件页数： | 62/85页 |
| 文件大小： | 0K |
| 描述： | MCU AVR 32K FLASH 8MHZ 64TQFP |
| 产品培训模块： | megaAVR Introduction |
| 标准包装： | 1,000 |
| 系列： | AVR® ATmega |
| 核心处理器： | AVR |
| 芯体尺寸： | 8-位 |
| 速度： | 8MHz |
| 连通性： | SPI，UART/USART，USI |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 54 |
| 程序存储器容量： | 32KB（16K x 16） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 1K x 8 |
| RAM 容量： | 2K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.8 V ~ 5.5 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 64-TQFP |
| 包装： | 带卷 (TR) |
| 其它名称： | ATMEGA325V-8AUR-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页当前第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页
37
2570N–AVR–05/11
ATmega325/3250/645/6450
10.6
Standby Mode
When the SM2..0 bits are 110 and an external crystal/resonator clock option is selected, the
SLEEP instruction makes the MCU enter Standby mode. This mode is identical to Power-down
with the exception that the Oscillator is kept running. From Standby mode, the device wakes up
in six clock cycles.
10.7
Power Reduction Register
The Power Reduction Register (PRR), see “PRR – Power Reduction Register” on page 40, pro-
vides a method to stop the clock to individual peripherals to reduce power consumption. The
current state of the peripheral is frozen and the I/O registers inaccessible. Resources used by
the peripheral when stopping the clock will remain occupied so the peripheral should be disabled
before stopping the clock. Waking up a peripheral, which is done by clearing the bit in PRR, puts
the peripheral in the same state as before shutdown.
Peripheral shutdown can be used in Idle mode and Active mode to reduce the overall power
consumption. In all other sleep modes, the clock is already stopped.
10.8
Minimizing Power Consumption
There are several possibilities to consider when trying to minimize the power consumption in an
AVR controlled system. In general, sleep modes should be used as much as possible, and the
sleep mode should be selected so that as few as possible of the device’s functions are operat-
ing. All functions not needed should be disabled. In particular, the following modules may need
special consideration when trying to achieve the lowest possible power consumption.
10.8.1
Analog to Digital Converter
If enabled, the ADC will be enabled in all sleep modes. To save power, the ADC should be dis-
abled before entering any sleep mode. When the ADC is turned off and on again, the next
conversion will be an extended conversion. Refer to “Analog to Digital Converter” on page 201
for details on ADC operation.
10.8.2
Analog Comparator
When entering Idle mode, the Analog Comparator should be disabled if not used. When entering
ADC Noise Reduction mode, the Analog Comparator should be disabled. In other sleep modes,
the Analog Comparator is automatically disabled. However, if the Analog Comparator is set up
to use the Internal Voltage Reference as input, the Analog Comparator should be disabled in all
sleep modes. Otherwise, the Internal Voltage Reference will be enabled, independent of sleep
mode. Refer to “Analog Comparator” on page 197 for details on how to configure the Analog
Comparator.
10.8.3
Brown-out Detector
If the Brown-out Detector is not needed by the application, this module should be turned off. If
the Brown-out Detector is enabled by the BODLEVEL Fuses, it will be enabled in all sleep
modes, and hence, always consume power. In the deeper sleep modes, this will contribute sig-
nificantly to the total current consumption. Refer to “Brown-out Detection” on page 43 for details
on how to configure the Brown-out Detector.
10.8.4
Internal Voltage Reference
The Internal Voltage Reference will be enabled when needed by the Brown-out Detection, the
Analog Comparator or the ADC. If these modules are disabled as described in the sections
相关PDF资料 |
PDF描述 |
|---|---|
| MS27499E18A11S | CONN RCPT 11POS BOX MNT W/SCKT |
| VI-23B-IY | CONVERTER MOD DC/DC 95V 50W |
| MS3121F-10-6S | CONN RECEPT 6POS W/SOCKT CRIMP |
| MS27656T23B21P | CONN RCPT 21POS WALL MNT W/PINS |
| AT89C5130A-RDRUM | MCU 8051 16K FLASH USB 64-VQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATmega325V-8MI | 功能描述:8位微控制器 -MCU AVR 32K FLASH 1K EE 2K SRAM ADC 1.8V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ATmega325V-8MU | 功能描述:8位微控制器 -MCU AVR 32K FLASH 1K EE 2K SRAM ADC 1.8V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ATMEGA325V-8MUR | 功能描述:8位微控制器 -MCU AVR 32K FLSH 2K SRAM 1KB EE-8MHz IND,1.8V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ATMEGA328 | 制造商:Arduino 功能描述:Atmel Atmega328 MCU w/Arduino bootloader |
| ATMEGA328-AU | 功能描述:8位微控制器 -MCU AVR 32K FLSH 1K EE2K SRAM-20MHz IND RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。