收藏本站
参数资料
型号： ATMEGA6490-16AI
厂商： Atmel
文件页数： 108/146页
文件大小： 0K
描述： IC AVR MCU FLASH 64K 5V 100TQFP
产品培训模块： megaAVR Introduction
标准包装： 90
系列： AVR® ATmega
核心处理器： AVR
芯体尺寸： 8-位
速度： 16MHz
连通性： SPI，UART/USART，USI
外围设备： 欠压检测/复位，LCD，POR，PWM，WDT
输入/输出数： 68
程序存储器容量： 64KB（32K x 16）
程序存储器类型： 闪存
EEPROM 大小： 2K x 8
RAM 容量： 4K x 8
电压 - 电源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
数据转换器： A/D 8x10b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 100-TQFP
包装： 托盘
配用： ATSTK600-TQFP100-ND - STK600 SOCKET/ADAPTER 100-TQFP
ATSTK504-ND - STARTER KIT AVR EXP MOD 100P LCD
38
2552K–AVR–04/11
ATmega329/3290/649/6490
the Analog Comparator is automatically disabled. However, if the Analog Comparator is set up
to use the Internal Voltage Reference as input, the Analog Comparator should be disabled in all
sleep modes. Otherwise, the Internal Voltage Reference will be enabled, independent of sleep
mode. Refer to “Analog Comparator” on page 207 for details on how to configure the Analog
Comparator.
9.7.3
Brown-out Detector
If the Brown-out Detector is not needed by the application, this module should be turned off. If
the Brown-out Detector is enabled by the BODLEVEL Fuses, it will be enabled in all sleep
modes, and hence, always consume power. In the deeper sleep modes, this will contribute sig-
nificantly to the total current consumption. Refer to “Brown-out Detection” on page 43 for details
on how to configure the Brown-out Detector.
9.7.4
Internal Voltage Reference
The Internal Voltage Reference will be enabled when needed by the Brown-out Detection, the
Analog Comparator or the ADC. If these modules are disabled as described in the sections
above, the internal voltage reference will be disabled and it will not be consuming power. When
turned on again, the user must allow the reference to start up before the output is used. If the
reference is kept on in sleep mode, the output can be used immediately. Refer to “Internal Volt-
age Reference” on page 44 for details on the start-up time.
9.7.5
Watchdog Timer
If the Watchdog Timer is not needed in the application, the module should be turned off. If the
Watchdog Timer is enabled, it will be enabled in all sleep modes, and hence, always consume
power. In the deeper sleep modes, this will contribute significantly to the total current consump-
tion. Refer to “Watchdog Timer” on page 45 for details on how to configure the Watchdog Timer.
9.7.6
Port Pins
When entering a sleep mode, all port pins should be configured to use minimum power. The
most important is then to ensure that no pins drive resistive loads. In sleep modes where both
the I/O clock (clk
I/O) and the ADC clock (clkADC) are stopped, the input buffers of the device will
be disabled. This ensures that no power is consumed by the input logic when not needed. In
some cases, the input logic is needed for detecting wake-up conditions, and it will then be
enabled. Refer to the section “Digital Input Enable and Sleep Modes” on page 64 for details on
which pins are enabled. If the input buffer is enabled and the input signal is left floating or have
an analog signal level close to V
CC/2, the input buffer will use excessive power.
For analog input pins, the digital input buffer should be disabled at all times. An analog signal
level close to V
CC/2 on an input pin can cause significant current even in active mode. Digital
input buffers can be disabled by writing to the Digital Input Disable Registers (DIDR1 and
DIDR0). Refer to “DIDR1 – Digital Input Disable Register 1” on page 210 and “DIDR0 – Digital
Input Disable Register 0” on page 227 for details.
9.7.7
JTAG Interface and On-chip Debug System
If the On-chip debug system is enabled by the OCDEN Fuse and the chip enter Power down or
Power save sleep mode, the main clock source remains enabled. In these sleep modes, this will
contribute significantly to the total current consumption. There are three alternative ways to
avoid this:
Disable OCDEN Fuse.
Disable JTAGEN Fuse.
相关PDF资料
PDF描述
ATMEGA649-16AI IC AVR MCU FLASH 64K 5V 64TQFP
ATMEGA645V-8AI IC AVR MCU FLASH 64K 1.8V 64TQFP
PIC16F767-I/SP IC PIC MCU FLASH 8KX14 28DIP
PIC16F76-I/SS IC MCU FLASH 8KX14 A/D 28SSOP
ATMEGA6450V-8AI IC AVR MCU FLASH 64K 1.8 100TQFP
相关代理商/技术参数
参数描述
ATmega6490-16AU 功能描述:8位微控制器 -MCU AVR 64K FLASH 2K EE 4K SRAM ADC LCD RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA6490-16AUR 功能描述:8位微控制器 -MCU AVR 64KB FLSH 2KB EE 4KB SRAM LCD16MHz,5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA6490A-AU 功能描述:8位微控制器 -MCU AVR 64KB FLSH 2KB EE 4KB SRAM-20MHz, IND RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA6490A-AUR 功能描述:8位微控制器 -MCU AVR 64KB FLSH 2KB EE 4KB SRAM-20MHz, IND RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA6490P-AU 功能描述:8位微控制器 -MCU AVR 64KB FLSH 2KB EE 4KB SRAM LCD-16MHz RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*