参数资料
| 型号： | ATSTK504 |
| 厂商： | Atmel |
| 文件页数： | 17/21页 |
| 文件大小： | 0K |
| 描述： | STARTER KIT AVR EXP MOD 100P LCD |
| 标准包装： | 1 |
| 附件类型： | STK500 扩展模块 |
| 适用于相关产品： | 100 引脚 LCD AVR 设备 |
| 配用： | ATSTK500-ND - PROGRAMMER AVR STARTER KIT |
| 相关产品： | ATMEGA3290PV-10AU-ND - IC MCU 32K 4X40 LCD CTRL 100TQFP ATMEGA3290P-20AU-ND - IC MCU 32K 4X40 LCD CTRL 100TQFP ATMEGA3250PV-10AU-ND - IC MCU AVR 32K FLASH 100-TQFP ATMEGA3250P-20AU-ND - IC MCU AVR 32K FLASH 100-TQFP ATMEGA6490V-8AI-ND - IC AVR MCU FLASH 64K 1.8 100TQFP ATMEGA6490-16AI-ND - IC AVR MCU FLASH 64K 5V 100TQFP ATMEGA6450V-8AI-ND - IC AVR MCU FLASH 64K 1.8 100TQFP ATMEGA6450-16AI-ND - IC AVR MCU FLASH 64K 5V 100TQFP ATMEGA6450V-8AU-ND - IC AVR MCU FLASH 64K 100TQFP ATMEGA6450-16AU-ND - IC AVR MCU FLASH 64K 100TQFP 更多... |
High-Voltage
programming
does not
work.
High-Voltage
The BSEL2, OSCSEL,
RESET and VTARGET
jumpers on STK500
are not set right. The
jumper on pin 6 and 8
on the PORTG header
is not mounted
The STK504 clock
See the Programming the AVR chapter for
setup.
Set the switch to the EXT position. See
programming switch is in the wrong
also Programming the AVR.
does not
position.
work.
General problems
Problem
Some of the
port pins are
not working .
Cause
The AVR is not
properly mounted in
the ZIF socket.
Solution
Make sure the chip is properly aligned in
the socket. When the spring-loaded latch
is released, the chip should fit nicely into
the bottom of the socket.
The code isn't The AVR has
According to the clock fuse setting, select
running.
The AVR will
not run on x
no/wrong clock
source.
The clock frequency
is exceeding the
the appropriate clock source on STK500
and STK504. Check the OSCSEL jumper
on STK500 and clock switch on STK504. If
you are using a crystal in one of the
sockets, check that it is firmly mounted in
its socket.
Check that you are running the AVR
within specifications. Check the speed
MHz, but
works ok on
clock rate of the AVR grade of the AVR and consult the
(at a certain operating datasheet for operating frequencies and
lower
frequencies.
The AVR will
not run on x
MHz, but
voltage).
Crystals should be
placed in the crystal
socket on STK504.
voltages.
Place the crystal in the socket on STK504.
Set the clock switch to the HF position.
works ok on
lower
frequencies. I
have a x MHz
crystal
mounted on
STK500
17
相关PDF资料 |
PDF描述 |
|---|---|
| ATSTK505 | ADAPTER KIT FOR 14PIN AVR MCU |
| ATSTK520 | ADAPTER KIT FOR 90PWM |
| ATSTK521 | EXPANSION MODULE ATSTK500 |
| ATSTK524 | KIT STARTER ATMEGA32M1/MEGA32C1 |
| ATSTK525 | KIT STARTER FOR AT90USB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATSTK505 | 功能描述:插座和适配器 Expansion module for STK500 Dev Board RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| ATSTK520 | 功能描述:开发板和工具包 - AVR AVR Starter Kit Ext 8K FLASH 3PSC RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| ATSTK521 | 功能描述:子卡和OEM板 ATSTK500 expansion module for AT90PWM81 RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| ATSTK524 | 功能描述:开发板和工具包 - AVR Starter Kit for ATMEGA32M1/C1 RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| ATSTK525 | 功能描述:开发板和工具包 - AVR Starter Kit for the AT90USB microcntrllr RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
发布紧急采购，3分钟左右您将得到回复。