参数资料
| 型号： | ATSTK504 |
| 厂商： | Atmel |
| 文件页数： | 9/21页 |
| 文件大小： | 0K |
| 描述： | STARTER KIT AVR EXP MOD 100P LCD |
| 标准包装： | 1 |
| 附件类型： | STK500 扩展模块 |
| 适用于相关产品： | 100 引脚 LCD AVR 设备 |
| 配用： | ATSTK500-ND - PROGRAMMER AVR STARTER KIT |
| 相关产品： | ATMEGA3290PV-10AU-ND - IC MCU 32K 4X40 LCD CTRL 100TQFP ATMEGA3290P-20AU-ND - IC MCU 32K 4X40 LCD CTRL 100TQFP ATMEGA3250PV-10AU-ND - IC MCU AVR 32K FLASH 100-TQFP ATMEGA3250P-20AU-ND - IC MCU AVR 32K FLASH 100-TQFP ATMEGA6490V-8AI-ND - IC AVR MCU FLASH 64K 1.8 100TQFP ATMEGA6490-16AI-ND - IC AVR MCU FLASH 64K 5V 100TQFP ATMEGA6450V-8AI-ND - IC AVR MCU FLASH 64K 1.8 100TQFP ATMEGA6450-16AI-ND - IC AVR MCU FLASH 64K 5V 100TQFP ATMEGA6450V-8AU-ND - IC AVR MCU FLASH 64K 100TQFP ATMEGA6450-16AU-ND - IC AVR MCU FLASH 64K 100TQFP 更多... |
To be able to program the AVR using ISP proramming, the AVR must have ISP
programming enabled (the ISP programming enable fuse must be set). ISP
programming can be enabled by High-Voltage Programming or JTAG
Programming .
Please consult the Fuses section in the STK500 documentation.
High-Voltage programming
High-Voltage Programming requires the target voltage to be set to 5V. If you
have any external hardware connected to STK504/STK500 that doesn not
tolerate 5V, it must be disconnected before you High-Voltage program the AVR.
To program the AVR mounted on STK504 using High-Voltage Programming,
follow these steps:
1. Turn off the STK500 power switch
2. Disconnect from STK500 and STK504 any hardware that does not tolerate
5V.
3. Connect the PROGCTRL to PORTD and PROGDATA to PORTB on the
STK500 as shown on the figure 4-2 below.
4. Set jumpers and switches accroding to this table 4-1.
5. Turn on STK500 power.
6. Then start the AVR Programmer found on the Tools menu in AVR Studio
("Tools/Program AVR/ Connect...")
Figure 4-2: High-Voltage programming setup
9
相关PDF资料 |
PDF描述 |
|---|---|
| ATSTK505 | ADAPTER KIT FOR 14PIN AVR MCU |
| ATSTK520 | ADAPTER KIT FOR 90PWM |
| ATSTK521 | EXPANSION MODULE ATSTK500 |
| ATSTK524 | KIT STARTER ATMEGA32M1/MEGA32C1 |
| ATSTK525 | KIT STARTER FOR AT90USB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATSTK505 | 功能描述:插座和适配器 Expansion module for STK500 Dev Board RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| ATSTK520 | 功能描述:开发板和工具包 - AVR AVR Starter Kit Ext 8K FLASH 3PSC RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| ATSTK521 | 功能描述:子卡和OEM板 ATSTK500 expansion module for AT90PWM81 RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| ATSTK524 | 功能描述:开发板和工具包 - AVR Starter Kit for ATMEGA32M1/C1 RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| ATSTK525 | 功能描述:开发板和工具包 - AVR Starter Kit for the AT90USB microcntrllr RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
发布紧急采购，3分钟左右您将得到回复。