参数资料
| 型号： | ATTINY15L-1SI |
| 厂商： | Atmel |
| 文件页数： | 31/85页 |
| 文件大小： | 0K |
| 描述： | IC AVR MCU 1K FLASH 2.7V SO8 |
| 标准包装： | 95 |
| 系列： | AVR® ATtiny |
| 核心处理器： | AVR |
| 芯体尺寸： | 8-位 |
| 速度： | 1.6MHz |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 6 |
| 程序存储器容量： | 1KB（512 x 16） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 64 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 数据转换器： | A/D 4x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.209"，5.30mm 宽） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页
37
ATtiny15L
1187H–AVR–09/07
The EEPROM Control Register
– EECR
Bit 7..4 – RES: Reserved Bits
These bits are reserved bits in the ATtiny15L and will always read as zero.
Bit 3 – EERIE: EEPROM Ready Interrupt Enable
When the I-bits in SREG and EERIE are set (one), the EEPROM Ready Interrupt is
enabled. When cleared (zero), the interrupt is disabled. The EEPROM Ready Interrupt
generates a constant interrupt when EEWE is cleared (zero).
Bit 2 – EEMWE: EEPROM Master Write Enable
The EEMWE bit determines whether setting EEWE to one causes the EEPROM to be
written. When EEMWE is set (one), setting EEWE will write data to the EEPROM at the
selected address. If EEMWE is zero, setting EEWE will have no effect. When EEMWE
has been set (one) by software, hardware clears the bit to zero after four clock cycles.
See the description of the EEWE bit for an EEPROM write procedure.
Bit 1 – EEWE: EEPROM Write Enable
The EEPROM Write Enable Signal – EEWE – is the write strobe to the EEPROM. When
address and data are correctly set up, the EEWE bit must be set to write the value in to
the EEPROM. The EEMWE bit must be set when the logical “1” is written to EEWE, oth-
erwise no EEPROM write takes place. The following procedure should be followed
when writing the EEPROM (the order of steps 2 and 3 is not essential):
1.
Wait until EEWE becomes zero.
2.
Write new EEPROM address to EEAR (optional).
3.
Write new EEPROM data to EEDR (optional).
4.
Write a logical “1” to the EEMWE bit in EECR.
5.
Within four clock cycles after setting EEMWE, write a logical “1” to EEWE.
Caution: An interrupt between step 4 and step 5 will make the write cycle fail, since the
EEPROM Master Write Enable will time-out. If an interrupt routine accessing the
EEPROM is interrupting another EEPROM access, the EEAR or EEDR Register will be
modified, causing the interrupted EEPROM access to fail. It is recommended to have
the Global Interrupt Flag cleared during the four last steps to avoid these problems.
When the write access time (typically 5.1 ms if the internal RC Oscillator is calibrated to
1.6 MHz) has elapsed, the EEWE bit is cleared (zero) by hardware. The user software
can poll this bit and wait for a zero before writing the next byte. When EEWE has been
set, the CPU is halted for two cycles before the next instruction is executed.
Bit 0 – EERE: EEPROM Read Enable
The EEPROM Read Enable Signal EERE is the read strobe to the EEPROM. When the
correct address is set up in the EEAR Register, the EERE bit must be set. When the
EERE bit is cleared (zero) by hardware, requested data is found in the EEDR Register.
The EEPROM read access takes one instruction and there is no need to poll the EERE
bit. When EERE has been set, the CPU is halted for four cycles before the next instruc-
tion is executed.
Bit
7
65
43
2
1
0
$1C
–
EERIE
EEMWE
EEWE
EERE
EECR
Read/Write
R
R/W
Initial value
0
X
0
相关PDF资料 |
PDF描述 |
|---|---|
| ATTINY15L-1SC | IC AVR MCU 1K FLASH 2.7V SO8 |
| ATTINY15L-1PI | IC AVR MCU 1K FLASH 2.7V 8DIP |
| ATTINY15L-1PC | IC AVR MCU 1K FLASH 2.7V 8DIP |
| AT89C2051-24SI | MICRO CONTROLLER |
| AT90S8515-8JC | IC MCU 8K FLSH 8MHZ 44PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATTINY15L-1SI SL383 | 制造商:Atmel Corporation 功能描述:MCU 8-bit ATtiny AVR RISC 1KB Flash 3.3V/5V 8-Pin SOIC EIAJ T/R |
| ATTINY15L-1SITRSL#QS309 | 制造商:Atmel Corporation 功能描述:ATLATTINY15L-1SITRSL#QS309 PGMD FOR AAPL |
| ATTINY15L-1SU | 功能描述:8位微控制器 -MCU AVR 1K FLASH 64B EE ADC 3V 1.6MHZ RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ATTINY15L-1SU SL383 | 制造商:Atmel Corporation 功能描述:AVR, 1K FLASH, 64B EE, ADC, 8 |
| ATTINY15POD | 功能描述:仿真器/模拟器 AVR ICE10 POD REPLACEMENT RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2 |
发布紧急采购，3分钟左右您将得到回复。